LINUX.ORG.RU

поставить нормальную систему охлаждения, которой не требуются высокие обороты для отвода того же количества тепла

anonymous ()
Ответ на: комментарий от MaxPower

Как не пробовал не получается, а пвм не пашет что то:

sudo pwmconfig
[sudo] пароль для user:       
# pwmconfig revision 6243 (2014-03-20)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.

We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.

/usr/sbin/pwmconfig: There are no fan-capable sensor modules installed

IhaveLinux ()
Ответ на: комментарий от IhaveLinux

Не знаю поможет или нет:

# sensors
nouveau-pci-2700
Adapter: PCI adapter
GPU core:     +0.90 V  (min =  +0.88 V, max =  +1.08 V)
temp1:        +37.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +105.0°C, hyst =  +5.0°C)
                       (emerg = +135.0°C, hyst =  +5.0°C)

k10temp-pci-00c3
Adapter: PCI adapter
Vcore:        +1.44 V  
Vsoc:         +1.09 V  
Tdie:         +46.4°C  
Tctl:         +46.4°C  
Tccd1:        +41.0°C  
Icore:       +14.00 A  
Isoc:         +7.00 A  

IhaveLinux ()
Ответ на: комментарий от anonymous

Автоматическая частота в биосе, я пока не гнал, так как нету потребности!

# sensors-detect 
# sensors-detect revision 6284 (2015-05-31 14:00:33 +0200)
# System: Micro-Star International Co., Ltd. MS-7B79 [2.0]
# Board: Micro-Star International Co., Ltd. X470 GAMING PLUS (MS-7B79)
# Kernel: 5.6.0-050600-lowlatency x86_64
# Processor: AMD Ryzen 7 3700X 8-Core Processor (23/113/0)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): 
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Intel digital thermal sensor...                             No
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): 
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found unknown chip with ID 0xd352

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): 
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no): 
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): 
Found unknown SMBus adapter 1022:790b at 0000:00:14.0.
Sorry, no supported PCI bus adapters found.



Остальное не влезло сюда написал - https://pastebin.com/xSYX9Pwh

IhaveLinux ()
Ответ на: комментарий от anonymous

Как я посмотрел тут на этом форуме тоже челу не кто командами не помог, а всякие резисторы ne555 и lm317… я купил комп не для колхоза! Мне нужно что бы работало как на Windows, без проблем то есть. На Windows другие проблемы особо критичные бесит аж… Я хочу перейти на норм систему но что бы она нормально работала с моими устройствами, не ужели так сложно… блин я не знаю кто знает, решил тут знают, но видимо надо кричать по всех форумах и везде … как так…

IhaveLinux ()
Ответ на: комментарий от anonymous

Сбросил вольтаж на проце ситуация не изменилась!

# sensors
nouveau-pci-2700
Adapter: PCI adapter
GPU core:     +0.90 V  (min =  +0.88 V, max =  +1.08 V)
temp1:        +36.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +105.0°C, hyst =  +5.0°C)
                       (emerg = +135.0°C, hyst =  +5.0°C)

k10temp-pci-00c3
Adapter: PCI adapter
Vcore:        +1.10 V  
Vsoc:         +1.08 V  
Tdie:         +38.9°C  
Tctl:         +38.9°C  
Tccd1:        +38.0°C  
Icore:       +11.00 A  
Isoc:         +7.00 A  


IhaveLinux ()
Ответ на: комментарий от IhaveLinux

Тут только осталось понять как дальше

# modprobe nct6775

# sensors
nct6795-isa-0a20
Adapter: ISA adapter
in0:                    +0.42 V  (min =  +0.00 V, max =  +1.74 V)
in1:                    +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in2:                    +3.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in3:                    +3.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:                    +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                    +0.15 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                    +0.78 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in7:                    +3.34 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in8:                    +3.23 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in9:                    +1.84 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                   +0.00 V  (min =  +0.00 V, max =  +0.00 V)
in11:                   +0.73 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                   +1.10 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                   +0.68 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                   +1.55 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                     0 RPM  (min =    0 RPM)
fan2:                  1445 RPM  (min =    0 RPM)
fan3:                     0 RPM  (min =    0 RPM)
fan4:                     0 RPM  (min =    0 RPM)
fan5:                     0 RPM  (min =    0 RPM)
fan6:                     0 RPM  (min =    0 RPM)
SYSTIN:                 +33.0°C  (high = +127.0°C, hyst =  +0.0°C)  sensor = CPU diode
CPUTIN:                 +35.0°C  (high = +125.0°C, hyst = +105.0°C)  sensor = thermistor
AUXTIN0:                +38.0°C  (high = +127.0°C, hyst =  +0.0°C)  ALARM  sensor = thermistor
AUXTIN1:               -128.0°C    sensor = thermistor
AUXTIN2:                +41.0°C    sensor = thermistor
AUXTIN3:                 -3.0°C    sensor = thermistor
SMBUSMASTER 0:          +39.5°C  (high = +125.0°C, hyst = +105.0°C)
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C  
PCH_CHIP_TEMP:           +0.0°C  
PCH_CPU_TEMP:            +0.0°C  
intrusion0:            ALARM
intrusion1:            ALARM
beep_enable:           disabled

nouveau-pci-2700
Adapter: PCI adapter
GPU core:     +0.90 V  (min =  +0.88 V, max =  +1.08 V)
temp1:        +37.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +105.0°C, hyst =  +5.0°C)
                       (emerg = +135.0°C, hyst =  +5.0°C)

k10temp-pci-00c3
Adapter: PCI adapter
Vcore:        +1.09 V  
Vsoc:         +1.08 V  
Tdie:         +39.4°C  
Tctl:         +39.4°C  
Tccd1:        +40.2°C  
Icore:       +11.00 A  
Isoc:         +7.00 A  

IhaveLinux ()
Ответ на: комментарий от IhaveLinux

Вышло конфиг сделать, но проблема в том, что не стало ниже крутится,

/etc/fancontrol ...

Common settings:
  INTERVAL=10

Settings for hwmon0/pwm1:
  Depends on hwmon1/temp1_input
  Controls 
  MINTEMP=36
  MAXTEMP=67
  MINSTART=1
  MINSTOP=100
  MINPWM=0
  MAXPWM=255

IhaveLinux ()