LINUX.ORG.RU

Монтирование Sony Ericsson S312 в Gentoo Linux


0

0

При подключении телефона SE S312 через USB появляется /dev/sdb, однако смонтировать что бы взять оттуда файлы не получается.

# ls /dev/sd*
/dev/sdb
# mount /dev/sdb /mnt/phone
mount: /dev/sdb: unknown device
#

Плеер, а также другой телефон монтируются нормально, только появляется не только /dev/sdb но и /dev/sdb1.

При загрузке с Gentoo Minimal Installation CD монтируется нормально и передаются файлы. Наверно в ядре нужны какие то дополнительные опции что бы смонтировать этот телефон, только вот какие. Незнаю как определить, в minimal CD до фига драйверов в ядре и как модули.

Ребят, помогите кто знает.

Ответ на: комментарий от AITap

Вот в моей системе, позже выложу в minimal CD.

usb 4-2: new full speed USB device using ohci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usb 4-2: USB disconnect, address 3
usb 4-2: new full speed USB device using ohci_hcd and address 4
usb 4-2: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
scsi 1:0:0:0: Direct-Access     SonyEric  Mobile Storage  0002 PQ: 0 ANSI: 0
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sdb] Attached SCSI removable disk
usb-storage: device scan complete
usb 4-2: USB disconnect, address 4
usb 4-2: new full speed USB device using ohci_hcd and address 5
usb 4-2: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access     SonyEric  Mobile Storage  0002 PQ: 0 ANSI: 0
sd 2:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
sd 2:0:0:0: [sdb] Attached SCSI removable disk
usb 4-2: USB disconnect, address 5
usb 4-2: new full speed USB device using ohci_hcd and address 6
usb 4-2: device descriptor read/64, error -62
usb 4-2: device descriptor read/64, error -62
usb 4-2: new full speed USB device using ohci_hcd and address 7
usb 4-2: device descriptor read/64, error -62
usb 4-2: device descriptor read/64, error -62
usb 4-2: new full speed USB device using ohci_hcd and address 8
usb 4-2: device not accepting address 8, error -62
usb 4-2: new full speed USB device using ohci_hcd and address 9
usb 4-2: device not accepting address 9, error -62
hub 4-0:1.0: unable to enumerate USB device on port 2
par12b12 ()
Ответ на: комментарий от par12b12

Вот то что в Minimal Live CD

usb 4-2: new full speed USB device using ohci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x0fce, Product: 0xe127, Revision: 0x0000
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: *** thread sleeping.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 1
usb-storage: device scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage:  12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 4:0:0:0: Direct-Access     SonyEric  Mobile Storage  0002 PQ: 0 ANSI: 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage:  12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 36 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
scsi 4:0:0:1: Direct-Access     SonyEric  Mobile Storage  0002 PQ: 0 ANSI: 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:2)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x4 L 18 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x2, ASC: 0x3a, ASCQ: 0x0
usb-storage: Not Ready: Medium not present
usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
sd 4:0:0:0: [sda] Attached SCSI removable disk
sd 4:0:0:0: Attached scsi generic sg0 type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x1
usb-storage: -- transport indicates command failure
usb-storage: Issuing auto-REQUEST_SENSE
usb-storage: Bulk Command S 0x43425355 T 0x6 L 18 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries
usb-storage: Status code 0; transferred 18/18
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0
usb-storage: -- Result from auto-sense is 0
usb-storage: -- code: 0x70, key: 0x6, ASC: 0x28, ASCQ: 0x0
usb-storage: Unit Attention: Not ready to ready change, medium may have changed

par12b12 ()
Ответ на: комментарий от par12b12

Продолжение

usb-storage: scsi cmd done, result=0x2
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage:  25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x8 L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 4:0:0:1: [sdb] 32768 512-byte hardware sectors (17 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage:  1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0x9 L 192 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
usb-storage: Status code -121; transferred 12/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 4:0:0:1: [sdb] Write Protect is off
sd 4:0:0:1: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:1: [sdb] Assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xa L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage:  1e 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage:  00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xc L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete

par12b12 ()
Ответ на: комментарий от par12b12

Ещё

usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage:  25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 8 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 8 bytes, 1 entries
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 4:0:0:1: [sdb] 32768 512-byte hardware sectors (17 MB)
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command MODE_SENSE (6 bytes)
usb-storage:  1a 00 3f 00 c0 00
usb-storage: Bulk Command S 0x43425355 T 0xe L 192 F 128 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 192 bytes, 1 entries
usb-storage: Status code -121; transferred 12/192
usb-storage: -- short read transfer
usb-storage: Bulk data transfer result 0x1
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 4:0:0:1: [sdb] Write Protect is off
sd 4:0:0:1: [sdb] Mode Sense: 0b 00 00 08
sd 4:0:0:1: [sdb] Assuming drive cache: write through
 sdb:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xf L 4096 F 128 Trg 0 LUN 1 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
 unknown partition table
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command ALLOW_MEDIUM_REMOVAL (6 bytes)
usb-storage:  1e 00 00 00 00 00

par12b12 ()
Ответ на: комментарий от par12b12
usb-storage: Bulk Command S 0x43425355 T 0x10 L 0 F 0 Trg 0 LUN 1 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x10 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sd 4:0:0:1: [sdb] Attached SCSI removable disk
sd 4:0:0:1: Attached scsi generic sg1 type 0
par12b12 ()
Ответ на: комментарий от par12b12

Так как пофиксить? Неужели никто не знает(( Где можно посмотреть что означает ошибка -62?

par12b12 ()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.