Помогите настроить 100Гц

Дальше

********************************************************************* # Graphics device section # **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device:

Section "Device"

Identifier "Standard VGA"

VendorName "ati"

BoardName "ati"

# The chipset line is optional in most cases. It can be used to override

# the driver's chipset detection, and should not normally be specified.

# Chipset "generic"

# The Driver line must be present. When using run-time loadable driver

# modules, this line instructs the server to load the specified driver

# module. Even when not using loadable driver modules, this line

# indicates which driver should interpret the information in this section.

Driver "vga"

# The BusID line is used to specify which of possibly multiple devices

# this section is intended for. When this line isn't present, a device

# section can only match up with the primary video device. For PCI

# devices a line like the following could be used. This line should not

# normally be included unless there is more than one video device

# installed.

# BusID "PCI:0:10:0"

# VideoRam 256

# Clocks 25.2 28.3

EndSection

# === ATI device section ===

Section "Device"

Identifier "ATI Graphics Adapter"

Driver "fglrx"

# ### generic DRI settings ###

# === disable PnP Monitor ===

#Option "NoDDC"

# === disable/enable XAA/DRI ===

Option "no_accel" "no"

Option "no_dri" "no"

# === misc DRI settings ===

Option "mtrr" "off" # disable DRI mtrr mapper, driver has its own code for mtrr

# ### FireGL DDX driver module specific settings ###

# === Screen Management ===

Option "DesktopSetup" "0x00000100"

Option "MonitorLayout" "AUTO, AUTO"

Option "IgnoreEDID" "off"

Option "HSync2" "unspecified"

Option "VRefresh2" "unspecified"

Option "ScreenOverlap" "0"

# === TV-out Management ===

Option "NoTV" "yes"

Option "TVStandard" "NTSC-M"

Option "TVHSizeAdj" "0"

Option "TVVSizeAdj" "0"

Option "TVHPosAdj" "0"

Option "TVVPosAdj" "0"

Option "TVHStartAdj" "0"

Option "TVColorAdj" "0"

Option "GammaCorrectionI" "0x06419064"

Option "GammaCorrectionII" "0x00000000"

# === OpenGL specific profiles/settings ===

Option "Capabilities" "0x00000000"

# === Video Overlay for the Xv extension ===

Option "VideoOverlay" "on"

# === OpenGL Overlay ===

# Note: When OpenGL Overlay is enabled, Video Overlay

# will be disabled automatically

Option "OpenGLOverlay" "off"

# === Center Mode (Laptops only) ===

Option "CenterMode" "off"

# === Pseudo Color Visuals (8-bit visuals) ===

Option "PseudoColorVisuals" "off"

# === QBS Management ===

Option "Stereo" "off"

Option "StereoSyncEnable" "1"

# === FSAA Management ===

Option "FSAAEnable" "no"

Option "FSAAScale" "1"

Option "FSAADisableGamma" "no"

Option "FSAACustomizeMSPos" "no"

Option "FSAAMSPosX0" "0.000000"

Option "FSAAMSPosY0" "0.000000"

Option "FSAAMSPosX1" "0.000000"

Option "FSAAMSPosY1" "0.000000"

Option "FSAAMSPosX2" "0.000000"

Option "FSAAMSPosY2" "0.000000"

Option "FSAAMSPosX3" "0.000000"

Option "FSAAMSPosY3" "0.000000"

Option "FSAAMSPosX4" "0.000000"

Option "FSAAMSPosY4" "0.000000"

Option "FSAAMSPosX5" "0.000000"

Option "FSAAMSPosY5" "0.000000"

# === Misc Options ===

Option "UseFastTLS" "0"

Option "BlockSignalsOnLock" "on"

Option "UseInternalAGPGART" "yes"

Option "ForceGenericCPU" "no"

BusID "PCI:1:0:0" # vendor=1002, device=4e4a

Screen 0

EndSection

**********************************************************************

# Screen sections

#

**********************************************************************

# Any number of screen sections may be present. Each describes

# the configuration of a single screen. A single specific screen section

# may be specified from the X server command line with the "-screen"

# option.

Section "Screen"

Identifier "Screen0"

Device "ATI Graphics Adapter"

Monitor "Monitor0"

DefaultDepth 24

#Option "backingstore"

Subsection "Display"

Depth 24

Modes "1280x1024"

ViewPort 0 0 # initial origin if mode is smaller than desktop

# Virtual 1280 1024

EndSubsection

EndSection

**********************************************************************

# ServerLayout sections.

#

**********************************************************************

Section "ServerLayout"

# The Identifier line must be present

Identifier "Server Layout"

Screen "Screen0"

InputDevice "Mouse1" "CorePointer"

InputDevice "Keyboard1" "CoreKeyboard"

EndSection

### EOF ###

а так?

Modeline "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync

Следуя из конфига, тебе нужно поправить одну строчечку:

Section "Screen"
Identifier "Screen0"
Device "ATI Graphics Adapter"
Monitor "Monitor0"
DefaultDepth 24
#Option "backingstore"
Subsection "Display"
Depth 24
#Modes "1280x1024"
Modes "1280x1024@100.00"
ViewPort 0 0 # initial origin if mode is smaller than desktop
# Virtual 1280 1024
EndSubsection
EndSection

grep -v '^\( *#\| *$\)'

Для начала залезь в спецификацию драйвера и прочитай, может ли он держать 100 герц. Это не шутка. У некоторых потолок в 85.

Потом убери нафиг параметры монитора - если у тебя иксы больше 4.3 или xorg, они смогут запросить верные параметры сами (есть исключение - старые мониторы типа samtron 55e могут опрашиваться неверно и это влияет на изображение).

А можно уточнить, какую именно часть можноудалить? Эту Section "Monitor" Identifier "Monitor0" HorizSync 30-110 VertRefresh 50-160 Option "DPMS" # 1280x1024 @ 100.00 Hz (GTF) hsync: 108.50 kHz; pclk: 190.96 MHz Modeline "1280x1024" 190.96 1280 1376 1520 1760 1024 1025 1028 1085 -HSync +Vsync EndSection

Эту Section "Device" Identifier "Standard VGA" VendorName "ati" BoardName "ati" # Chipset "generic" Driver "vga" # BusID "PCI:0:10:0" # VideoRam 256 # Clocks 25.2 28.3 EndSection

Или эту

Section "Screen" Identifier "Screen0" Device "ATI Graphics Adapter" Monitor "Monitor0" DefaultDepth 24 #Option "backingstore"

Subsection "Display" Depth 24 Modes "1280x1024" ViewPort 0 0 # initial origin if mode is smaller than desktop # Virtual 1280 1024 EndSubsection EndSection

Или чё-то другое

Добавлю к совету джакилла:

Все вынести, загрузить и посмотреть

$ xrandr
что он вообще умеет,
потом
$ gtf X Y Hz

И прописать