LINUX.ORG.RU

Flash-memory


0

0

Столкнулся с трудностью - не работает Flash память (проверил на винде работает). Каталог /proc/bus/usb есть. Драйвер usb-storage и файл /proc/scsi/scsi с написанным о Flash Attached Yes. При попытке выполнить mount -t vfat /dev/sda1 /mnt/flash виснет и на этой консоли ничего не выводится. Linux - Slackware 10.1. Заранее спасибо!

Ответ на: Re: Flash-memory от sova

Re: Flash-memory

hub.c: new USB device 00:02.2-1, assigned address 6 usb-storage: act_altsettting is 0 usb-storage: id_index calculated to be: 120 usb-storage: Array length appears to be: 122 usb-storage: USB Mass Storage device detected usb-storage: Endpoints: In: 0xcfb2a980 Out: 0xcfb2a994 Int: 0xcfb2a9a8 (Period 1) usb-storage: Found existing GUID 0ea02168106c11416a8934af WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 6 usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 00 00 00 3c c3 cf usb-storage: Bulk command S 0x43425355 T 0x1b Trg 0 LUN 0 L 0 F 0 CL 6 usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1b R 0 Stat 0x1 usb-storage: -- transport indicates command failure usb-storage: Issuing auto-REQUEST_SENSE usb-storage: Bulk command S 0x43425355 T 0x1c Trg 0 LUN 0 L 18 F 128 CL 6 usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_transfer_partial(): xfer 18 bytes usb-storage: usb_stor_bulk_msg() returned 0 xferred 18/18 usb-storage: usb_stor_transfer_partial(): transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1c R 0 Stat 0x0 usb-storage: -- Result from auto-sense is 0 usb-storage: -- code: 0x70, key: 0x6, ASC: 0x28, ASCQ: 0x0 usb-storage: Unit Attention: not ready to ready transition usb-storage: scsi cmd done, result=0x2 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened.

sda : READ CAPACITY failed. sda : status = 0, message = 00, host = 7, driver = 00 sda : sense not available. sda : block size assumed to be 512 bytes, disk size 1GB. sda: I/O error: dev 08:00, sector 0 I/O error: dev 08:00, sector 0 unable to read partition table usb.c: USB disconnect on device 00:02.2-1 address 6

dimanchik ()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.