Кол-во SMART ошибок переодически увеличиваются

... за счет вот таких ошибок

Error 52 occurred at disk power-on lifetime: 29103 hours (1212 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
 — -- — -- — -- --
04 51 fe 00 00 00 40 Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
 — -- — -- — -- — -- ---------------- --------------------
ef 05 fe 00 00 00 40 00 15d+13:56:47.375 SET FEATURES [Enable APM]
c8 00 10 7f 10 6c ec 00 15d+13:56:47.375 READ DMA
c8 00 08 6f 10 6c ec 00 15d+13:56:47.375 READ DMA
c8 00 68 d7 11 6c ec 00 15d+13:56:47.375 READ DMA
c8 00 08 c7 11 6c ec 00 15d+13:56:47.375 READ DMA


/var/log/kernel:
----------------
Nov 29 09:44:19 home kernel: ata1.00: configured for UDMA/100
Nov 29 09:44:19 home kernel: ata1.01: configured for UDMA/33
Nov 29 09:44:19 home kernel: ata1: EH complete
Nov 29 09:44:19 home kernel: ata3.00: configured for UDMA/133
Nov 29 09:44:19 home kernel: ata3: EH complete



SMART счетчики:
---------------
1 Raw_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 066 055 000 Pre-fail Always - 5888
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 685
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 253 253 051 Pre-fail Always - 0
8 Seek_Time_Performance 0x0024 253 253 000 Old_age Offline - 0
9 Power_On_Half_Minutes 0x0032 095 095 000 Old_age Always - 29104h+40m
10 Spin_Retry_Count 0x0013 253 253 049 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 474
194 Temperature_Celsius 0x0022 139 085 000 Old_age Always - 33
195 Hardware_ECC_Recovered 0x000a 100 100 000 Old_age Always - 110639818
196 Reallocated_Event_Count 0x0012 253 253 000 Old_age Always - 0
197 Current_Pending_Sector 0x0033 253 253 010 Pre-fail Always - 0
198 Offline_Uncorrectable 0x0031 253 253 010 Pre-fail Offline - 0
199 UDMA_CRC_Error_Count 0x000b 100 100 051 Pre-fail Always - 0
200 Multi_Zone_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0
201 Soft_Read_Error_Rate 0x000b 100 100 051 Pre-fail Always - 0


Я правильно понял, что ошибка произошла при выполнении «SET FEATURES [Enable APM]» и на это можно забить? Или уже пора бежать за новыми диском?