LINUX.ORG.RU
Форум — Linux-hardware  

Xorg intel видло i915g


0

0

Всем привет у меня такая проблема у меня на второй тачке стоит до бновления Ubuntu 9.04 но и в Xorg спокойно ставилось разрешение 1280x1024 но после обновления максимум ставится 1152x864 хочется вернуть прежнее разрешение

★★★★★
← Прошивка D-Link 2500U
radeonhd проблема при установке →

Покажи кусок лога:

grep Mode /var/log/Xorg.0.log

А вообще, если лень разбираться, есть такой костыль: xorg.conf. Там надо написать следующее (заменив только VendorName и ModelName, т.е. частоты уже указаны правильно для случая «1280x1024 LCD»):

Section "Monitor"
 Identifier "Monitor1"
 VendorName "Acer"
 ModelName "v193"
 Option "PreferredMode" "1280x1024"
 HorizSync 30-64
 VertRefresh 59-61
EndSection
AEP ★★★★★
()
Ответ на: комментарий от AEP 
/var/log/Xorg.0.log:(II) intel(0): Printing DDC gathered Modelines:
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync (68.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x0.0   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x0.0   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x0.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x0.0   31.50  640 664 704 832  480 489 492 520 -hsync -vsync (37.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x0.0   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x0.0   25.18  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "720x400"x0.0   35.50  720 738 846 900  400 421 423 449 -hsync -vsync (39.4 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "720x400"x0.0   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   78.75  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.0 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   44.90  1024 1032 1208 1264  768 768 772 817 interlace +hsync +vsync (35.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "832x624"x0.0   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x0.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x0.0   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1152x864"x0.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x0.0   36.00  640 696 752 832  480 481 484 509 -hsync -vsync (43.3 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x0.0   56.25  800 832 896 1048  600 601 604 631 +hsync +vsync (53.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x0.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync (68.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1280x1024"x0.0  108.00  1280 1328 1440 1688  1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x85.0   94.50  1024 1072 1168 1376  768 769 772 808 +hsync +vsync (68.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1152x864"x75.0  108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync (67.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x75.1   78.80  1024 1040 1136 1312  768 769 772 800 +hsync +vsync (60.1 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x70.1   75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync (56.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "1024x768"x60.0   65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync (48.4 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "832x624"x74.6   57.28  832 864 928 1152  624 625 628 667 -hsync -vsync (49.7 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x72.2   50.00  800 856 976 1040  600 637 643 666 +hsync +vsync (48.1 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x75.0   49.50  800 816 896 1056  600 601 604 625 +hsync +vsync (46.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x60.3   40.00  800 840 968 1056  600 601 605 628 +hsync +vsync (37.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "800x600"x56.2   36.00  800 824 896 1024  600 601 603 625 +hsync +vsync (35.2 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x72.8   31.50  640 664 704 832  480 489 491 520 -hsync -vsync (37.9 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x75.0   31.50  640 656 720 840  480 481 484 500 -hsync -vsync (37.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x66.7   30.24  640 704 768 864  480 483 486 525 -hsync -vsync (35.0 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "640x480"x60.0   25.20  640 656 752 800  480 490 492 525 -hsync -vsync (31.5 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "720x400"x87.8   35.50  720 738 846 900  400 421 423 449 -hsync -vsync (39.4 kHz)
/var/log/Xorg.0.log:(II) intel(0): Modeline "720x400"x70.1   28.32  720 738 846 900  400 412 414 449 -hsync +vsync (31.5 kHz)


у меня Samsung SyncMaster 753df

enep ★★★★★
() автор топика
Ответ на: комментарий от enep

И еще пожалуйста grep mode /var/log/Xorg.0.log (с маленькой буквы). Сразу не попросил, поскольку в моем логе этого просто нет.

AEP ★★★★★
()
Ответ на: комментарий от AEP

И еще пожалуйста grep mode /var/log/Xorg.0.log (с маленькой буквы). Сразу не попросил, поскольку в моем логе этого просто нет. 

(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output VGA1 using initial mode 1024x768
(**) Option "xkb_model" "pc105"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_model" "pc105"
(**) Option "xkb_model" "pc105"
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
(II) intel(0): First detailed timing is preferred mode
(II) intel(0): Printing probed modes for output VGA1
enep ★★★★★
() автор топика
Ответ на: комментарий от AEP 
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
	Function supported
	Call successful

	VBE version 300
	VBE string at 0x2110 "Intel(r)915G/915GV/910GL Graphics Chip Accelerated VGA BIOS"

VBE/DDC service about to be called
	Report DDC capabilities

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
	Function supported
	Call successful

	Monitor and video card combination does not support DDC1 transfers
	Monitor and video card combination supports DDC2 transfers
	0 seconds per 128 byte EDID block transfer
	Screen is not blanked during DDC transfer

Reading next EDID block

VBE/DDC service about to be called
	Read EDID

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
	Function supported
	Call successful

parse-edid: EDID checksum passed.

	# EDID version 1 revision 2
Section "Monitor"
	# Block type: 2:0 3:fd
	# Block type: 2:0 3:fc
	Identifier "S/M 753DF"
	VendorName "SAM"
	ModelName "S/M 753DF"
	# Block type: 2:0 3:fd
	HorizSync 30-70
	VertRefresh 50-160
	# Max dot clock (video bandwidth) 110 MHz
	# Block type: 2:0 3:fc
	# Block type: 2:0 3:ff
	# DPMS capabilities: Active off:yes  Suspend:yes  Standby:yes

	Mode 	"1024x768"	# vfreq 84.997Hz, hfreq 68.677kHz
		DotClock	94.500000
		HTimings	1024 1072 1168 1376
		VTimings	768 769 772 808
		Flags	"+HSync" "+VSync"
	EndMode
	# Block type: 2:0 3:fd
	# Block type: 2:0 3:fc
	# Block type: 2:0 3:ff
EndSection
root@enep-desktop:~# get-edid | parse-edid 
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
	Function supported
	Call successful

	VBE version 300
	VBE string at 0x2110 "Intel(r)915G/915GV/910GL Graphics Chip Accelerated VGA BIOS"

VBE/DDC service about to be called
	Report DDC capabilities

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
	Function supported
	Call successful

	Monitor and video card combination does not support DDC1 transfers
	Monitor and video card combination supports DDC2 transfers
	0 seconds per 128 byte EDID block transfer
	Screen is not blanked during DDC transfer

Reading next EDID block

VBE/DDC service about to be called
	Read EDID

	Performing real mode VBE call
	Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
	Function supported
	Call successful
enep ★★★★★
() автор топика
Ответ на: комментарий от enep

Криминала (кроме x0.0, но он есть и у меня) не вижу.

AEP ★★★★★
()
Ответ на: комментарий от enep

Вылечил задал параметр ядра i915.modeset=0

enep ★★★★★
() автор топика
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
← Прошивка D-Link 2500U
Linux-hardware
radeonhd проблема при установке →