acer extensa 5210
uname -a Linux nekrobook 2.6.23.1-10.fc7 #1 SMP Fri Oct 19 15:39:08 EDT 2007 i686 i686 i386 GNU/Linux
lspci -v 03:00.0 Network controller: Broadcom Corporation Dell Wireless 1390 WLAN Mini-PCI Card (rev 01) Subsystem: AMBIT Microsystem Corp. Unknown device 0422 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d8000000 (32-bit, non-prefetchable) [size]
Capabilities: [40] Power Management version 2 Capabilities: [58] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable- Capabilities: [d0] Express Legacy Endpoint IRQ 0 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel
после разных танцев с бубном запустил через /lib/modules/2.6.23.1-10.fc7/kernel/drivers/net/wireless/b43/b43.ko модуль главное что было сделано это распотрошён из виндового драйвера bcmwl5.sys утилитой b43-fwcutter
получилось из нее набор firmware
/lib/firmware/bcm43xx_initval01.fw /lib/firmware/bcm43xx_initval08.fw /lib/firmware/bcm43xx_initval21.fw /lib/firmware/bcm43xx_microcode4.fw /lib/firmware/bcm43xx_initval02.fw /lib/firmware/bcm43xx_initval09.fw /lib/firmware/bcm43xx_initval22.fw /lib/firmware/bcm43xx_microcode5.fw /lib/firmware/bcm43xx_initval03.fw /lib/firmware/bcm43xx_initval10.fw /lib/firmware/bcm43xx_initval23.fw /lib/firmware/bcm43xx_pcm4.fw /lib/firmware/bcm43xx_initval04.fw /lib/firmware/bcm43xx_initval17.fw /lib/firmware/bcm43xx_initval24.fw /lib/firmware/bcm43xx_pcm5.fw /lib/firmware/bcm43xx_initval05.fw /lib/firmware/bcm43xx_initval18.fw /lib/firmware/bcm43xx_initval25.fw /lib/firmware/bcm43xx_initval06.fw /lib/firmware/bcm43xx_initval19.fw /lib/firmware/bcm43xx_microcode11.fw /lib/firmware/bcm43xx_initval07.fw /lib/firmware/bcm43xx_initval20.fw /lib/firmware/bcm43xx_microcode13.fw
вроде как запустилась светодиод на панели загарается и тухнет по нажатию клавиши
iwconfig wlan0 IEEE 802.11g ESSID:"ssid" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2346 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0
iwlist wlan0 scan wlan0 No scan results
вот kismet так и не запустил
[root@nekrobook ~]# kismet Server options: none Client options: none Starting server... Will drop privs to kismet (498) gid 497 Enabling channel hopping. Enabling channel splitting. Source 0 (broadcom): Enabling monitor mode for bcm43xx source interface wlan0 channel 6... FATAL: Failed to set monitor mode: Device or resource busy. This usually means your drivers either do not support monitor mode, or use a different mechanism for getting to it. Make sure you have a version of your drivers that support monitor mode, and consult the troubleshooting section of the README. Waiting for server to start before starting UI...
/etc/kismet/kismet.conf
.... source=bcm43xx,wlan0,broadcom ....
что дальше
