Происходят периодические зависания после reboot
после строки
[ 6.760000] ledtrig-cpu: registered to indicate activity on CPUs
Ничего в гугле по этому поводу не нашел, кроме этого
https://github.com/RC-MODULE/linux-3.10.x/issues/7
От чего это может быть ?
Может кто решил эту проблему ?
Ниже все сообщения после ребута до момента зависания.
root@shadow:~# reboot
Broadcast message from root@shadow (ttyS0) (Tue Oct 27 10:43:41 2015):
The system is going down for reboot NOW!
INIT: Sending processes the TERM signal
[info] Using makefile-style concurrent boot in runlevel 6.
[info] Saving the system clock.
hwclock: Cannot access the Hardware Clock via any known method.
hwclock: Use the --debug option to see the details of our search for an access m
ethod.
[....] Asking all remaining processes to terminate...done.
[....] All processes ended within 1 seconds...done.
[....] Deconfiguring network interfaces...done.
[....] Deactivating swap...done.
[ 576.150000] UBIFS: background thread "ubifs_bgt0_0" stops
[info] Will now restart.
[ 578.430000] Restarting system.
[ 578.440000] platform: Requested system restart
MBOOT (K1879 and friends): Version mboot-00063-g9302e24-dirty (Built Thu Aug 21
17:10:13 MSK 2014)
OTP info: boot_source 2 jtag_stop 0 words_len 1024
Maximum bank size: 0x10000000 bytes
Detected 134217728 bytes of EM0 memory
MEMORY: 40000000 -> 48000000
Memory layout
0x00100010 early
0x001001C8 text
0x0011E9BC data
0x00127D40 signature
0x00127D44 bss_start
0x00135EB4 stack_start
0x00137FF8^ stack_ptr
0x00138000 malloc
0x0017F000 env
mnand_read_id: flash id 0xD3
mnand_read_id: flash ext_id 0x95
mnand_read_id: CS0 NAND 1GiB 3,3V 8-bit size(1024) writesize(2048) oobsize(64) e
rasesize(131072)
mnand_read_id: flash id 0x00
mnand_read_id: WARNING: Unknown flash ID. Using default (0xF1)
mnand_read_id: flash ext_id 0x00
mnand: Chip configurations differ, ignoring CS1
greth: Setting GRETH base addr to 0x20034000
greth: Found GRETH at 0x20034000, irq 255
greth: Resetting GRETH
greth: greth: 'phyaddr' not set, fall back to built-in table
greth: greth: using preset PHY addr: 1f
greth: Resetting the PHY
greth: write_mii: 0x20034010 < 0xB100F801 [p:31 a:0 d:0xB100]
greth: 10/100 GRETH Ethermac at [0x20034000] irq 255. Running 100 Mbps full dupl
ex
greth: PHY: Vendor 1f0 Device c Revision 4
greth: greth_init
greth: greth_init: enabling receiver
ETH new device: name GRETH_10/100
greth: GRETH: New MAC address: 02:00:f7:00:27:0f
USB thresholds: in 0x20 out 0x7e
Is there an EDCL emergency? Nope
edcl: Ethernet debug disabled by environment
MTD Partition: boot @ 0x00000000 size 0x00040000
MTD Partition: env @ 0x00040000 size 0x00020000
MTD Partition: dtb @ 0x00060000 size 0x00020000
MTD Partition: kernel @ 0x00080000 size 0x00400000
MTD Partition: rootfs @ 0x00480000 size 0x3FB80000
Hit any key (in 2 sec) to skip autoload...
Running autoload command 'mtdboot;bootm'
MTD Loading kernel image: dev kernel offset 0x000000000000 addr 0x40100000
Linux preparing to boot the kernel: machid 0xcd1
Using Flatterned Device Tree boot method
IMG moving image: type 2 from 0x40100040 to 0x40008000
HINT: To optimize boot time adjust loadaddr to: 0x40007fc0
Linux entry 0x40008000
USB thresholds: in 0x20 out 0x7e
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.10.28-shadow1-g0cdc7cb (rs1-unx@rs1unx) (gcc vers
ion 4.8.1 (crosstool-NG 1.19.0) ) #1 Thu Oct 15 12:43:31 MSK 2015
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr
=00c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruc
tion cache
[ 0.000000] Machine: Module MB77.07, model: Module MB77.07
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 23840
[ 0.000000] Kernel command line: console=ttyS0,38400n8 earlyprintk=serial ub
i.mtd=4,2048 root=ubi0:rootfs rootfstype=ubifs mtdparts=mnand:0x40000@0x0(boot),
0x20000@0x40000(env),0x20000@0x60000(dtb),0x400000@0x80000(kernel),0x3FB80000@0x
480000(rootfs)
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Memory: 94MB 0MB = 94MB total
[ 0.000000] Memory: 89200k/89200k available, 41872k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04b1a94 (4775 kB)
[ 0.000000] .init : 0xc04b2000 - 0xc04d533c ( 141 kB)
[ 0.000000] .data : 0xc04d6000 - 0xc0517df0 ( 264 kB)
[ 0.000000] .bss : 0xc0517df0 - 0xc0597a70 ( 512 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] regs = 0xf8000000, irq_start = 0
[ 0.000000] VIC @f8000000: id 0x00041192, vendor 0x41
[ 0.000000] regs = 0xf8010000, irq_start = 32
[ 0.000000] VIC @f8010000: id 0x00041192, vendor 0x41
[ 0.000000] UEMD: Firing up timer system
[ 0.000000] Clocksource: rate 54000000 mult 19418074 shift 20
[ 0.000000] Clockevent: rate 54000000 mult 231928233 shift 32
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps ever
y 4294967286ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.020000] Calibrating delay loop... 215.04 BogoMIPS (lpj=1075200)
[ 0.100000] pid_max: default: 32768 minimum: 301
[ 0.110000] Mount-cache hash table entries: 512
[ 0.120000] CPU: Testing write buffer coherency: ok
[ 0.130000] Setting up static identity map for 0xc0343390 - 0xc03433c8
[ 0.150000] devtmpfs: initialized
[ 0.160000] NET: Registered protocol family 16
[ 0.170000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.240000] OTP ROM is not flashed
[ 0.250000] msvdhd: configuring memory
[ 0.260000] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.270000] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.410000] bio: create slab <bio-0> at 0
[ 0.430000] SCSI subsystem initialized
[ 0.440000] ssp-pl022 2002e000.ssp: ARM PL022 driver, device ID: 0x00041022
[ 0.450000] pl022: mapped registers from 0x2002e000 to f802e000
[ 0.470000] usbcore: registered new interface driver usbfs
[ 0.480000] usbcore: registered new interface driver hub
[ 0.490000] usbcore: registered new device driver usb
[ 0.500000] media: Linux media interface: v0.10
[ 0.520000] Linux video capture interface: v2.00
[ 0.530000] Advanced Linux Sound Architecture Driver Initialized.
[ 0.550000] Switching to clocksource uemd_timer1
[ 0.650000] NET: Registered protocol family 2
[ 0.660000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.670000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.680000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.690000] TCP: reno registered
[ 0.700000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.710000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.720000] NET: Registered protocol family 1
[ 0.730000] RPC: Registered named UNIX socket transport module.
[ 0.740000] RPC: Registered udp transport module.
[ 0.750000] RPC: Registered tcp transport module.
[ 0.760000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.840000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.860000] NFS: Registering the id_resolver key type
[ 0.870000] Key type id_resolver registered
[ 0.880000] Key type id_legacy registered
[ 0.890000] msgmni has been set to 174
[ 0.910000] alg: No test for stdrng (krng)
[ 0.920000] io scheduler noop registered (default)
[ 0.940000] fj_gpio: Added 32 gpio lines at base -981095824
[ 0.960000] module_vdu 80173000.vdu: found VDU device at 80173000, id <ebebab
01>
[ 1.000000] Console: switching to colour frame buffer device 160x45
[ 1.040000] fb0: Module VDU frame buffer device
[ 1.090000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 1.110000] 2002b000.uart: ttyS0 at MMIO 0x2002b000 (irq = 7) is a 8250
[ 1.120000] console [ttyS0] enabled, bootconsole disabled
[ 1.120000] console [ttyS0] enabled, bootconsole disabled
[ 1.140000] 20022000.uart: ttyS1 at MMIO 0x20022000 (irq = 9) is a 8250
[ 1.150000] 2002c000.uart: ttyS2 at MMIO 0x2002c000 (irq = 8) is a 8250
[ 1.160000] [drm] Initialized drm 1.1.0 20060810
[ 1.190000] loop: module loaded
[ 1.200000] msvdhd 80180000.video_decoder: found device at 0x80180000, id 0x0
025300b
[ 1.250000] EasyNMC Unified DSP Framework. (c) RC Module 2014
[ 1.260000] easynmc-nmc3: imem at phys 0x140000 virt 0xc8900000 size 0x80000
bytes
[ 1.270000] easynmc-nmc3: HP IRQ 14 LP IRQ 15
[ 1.280000] easynmc: registering core K1879-nmc (nmc3) with id 0
[ 1.300000] mnand CS0 Samsung size(1024) writesize(2048) oobsize(64) erasesiz
e(131072)
[ 1.310000] mnand: Bad chip id or no chip at CS1
[ 1.320000] mnand: Detected 1073741824 bytes of NAND
[ 1.330000] 5 cmdlinepart partitions found on MTD device mnand
[ 1.340000] Creating 5 MTD partitions on "mnand":
[ 1.350000] 0x000000000000-0x000000040000 : "boot"
[ 1.370000] 0x000000040000-0x000000060000 : "env"
[ 1.390000] 0x000000060000-0x000000080000 : "dtb"
[ 1.410000] 0x000000080000-0x000000480000 : "kernel"
[ 1.450000] 0x000000480000-0x000040000000 : "rootfs"
[ 6.520000] libphy: greth-mdio: probed
[ 6.540000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.550000] uemd-ehci 10040000.ehci: UEMD EHCI
[ 6.560000] uemd-ehci 10040000.ehci: new USB bus registered, assigned bus num
ber 1
[ 6.570000] uemd-ehci 10040000.ehci: irq 35, io mem 0x10040000
[ 6.600000] uemd-ehci 10040000.ehci: USB 2.0 started, EHCI 1.00
[ 6.620000] hub 1-0:1.0: USB hub found
[ 6.630000] hub 1-0:1.0: 2 ports detected
[ 6.640000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.650000] usbcore: registered new interface driver usb-storage
[ 6.660000] usbcore: registered new interface driver usbserial
[ 6.670000] mousedev: PS/2 mouse device common for all mice
[ 6.680000] i2c /dev entries driver
[ 6.710000] module_hdmi: module_hdmi: Device ID: 0x9132
[ 6.720000] usbcore: registered new interface driver i2c-tiny-usb
[ 6.740000] sp805-wdt 20025000.wd: registration successful
[ 6.760000] ledtrig-cpu: registered to indicate activity on CPUs
