LINUX.ORG.RU

gentoo & usb


0

0

поставил сегодня gentoo 2006.0. не монтируются флешки. пишет примерно вот что:

# mount /dev/sda1 /mnt/sda
/dev/sda1 is not a valid block device

ядро самосборное, 2.6.16.18.

как заставить это дело работать?

вот фрагмент /var/log/messages:

May 24 11:58:37 friday usbmon: debugfs is not available
May 24 11:58:37 friday ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
May 24 11:58:37 friday PCI: setting IRQ 10 as level-triggered
May 24 11:58:37 friday ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
May 24 11:58:37 friday ehci_hcd 0000:00:10.3: EHCI Host Controller
May 24 11:58:37 friday ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
May 24 11:58:37 friday ehci_hcd 0000:00:10.3: irq 10, io mem 0xde000000
May 24 11:58:37 friday ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
May 24 11:58:37 friday usb usb1: configuration #1 chosen from 1 choice
May 24 11:58:37 friday hub 1-0:1.0: USB hub found
May 24 11:58:37 friday hub 1-0:1.0: 6 ports detected
May 24 11:58:37 friday USB Universal Host Controller Interface driver v2.3
May 24 11:58:37 friday ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
May 24 11:58:37 friday uhci_hcd 0000:00:10.0: UHCI Host Controller
May 24 11:58:37 friday uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
May 24 11:58:37 friday uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d000
May 24 11:58:37 friday usb usb2: configuration #1 chosen from 1 choice
May 24 11:58:37 friday hub 2-0:1.0: USB hub found
May 24 11:58:37 friday hub 2-0:1.0: 2 ports detected
May 24 11:58:37 friday ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
May 24 11:58:37 friday usb 1-4: new high speed USB device using ehci_hcd and address 2
May 24 11:58:37 friday ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
May 24 11:58:37 friday uhci_hcd 0000:00:10.1: UHCI Host Controller
May 24 11:58:37 friday uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
May 24 11:58:37 friday uhci_hcd 0000:00:10.1: irq 11, io base 0x0000d400
May 24 11:58:37 friday usb usb3: configuration #1 chosen from 1 choice
May 24 11:58:37 friday hub 3-0:1.0: USB hub found
May 24 11:58:37 friday hub 3-0:1.0: 2 ports detected
May 24 11:58:37 friday ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
May 24 11:58:37 friday ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
May 24 11:58:37 friday uhci_hcd 0000:00:10.2: UHCI Host Controller
May 24 11:58:37 friday uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
May 24 11:58:37 friday uhci_hcd 0000:00:10.2: irq 10, io base 0x0000d800
May 24 11:58:37 friday usb usb4: configuration #1 chosen from 1 choice
May 24 11:58:37 friday hub 4-0:1.0: USB hub found
May 24 11:58:37 friday hub 4-0:1.0: 2 ports detected
May 24 11:58:37 friday ehci_hcd 0000:00:10.3: Unlink after no-IRQ? Controller is probably using the wrong IRQ.
May 24 11:58:37 friday usb 1-4: device not accepting address 2, error -110
May 24 11:58:37 friday usb 1-4: new high speed USB device using ehci_hcd and address 3
May 24 11:58:37 friday usb 1-4: device not accepting address 3, error -110
May 24 11:58:37 friday usb 1-4: new high speed USB device using ehci_hcd and address 4
May 24 11:58:37 friday usb 1-4: device not accepting address 4, error -110
May 24 11:58:37 friday usb 1-4: new high speed USB device using ehci_hcd and address 5
May 24 11:58:37 friday usb 1-4: device not accepting address 5, error -110
May 24 11:58:37 friday usbcore: registered new driver usblp
May 24 11:58:37 friday drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
May 24 11:58:37 friday Initializing USB Mass Storage driver...
May 24 11:58:37 friday usbcore: registered new driver usb-storage
May 24 11:58:37 friday USB Mass Storage support registered.
May 24 11:58:37 friday usbcore: registered new driver usbhid
May 24 11:58:37 friday drivers/usb/input/hid-core.c: v2.6:USB HID core driver

★★★

Ответ на: Re: gentoo & usb от iRunix

Re: gentoo & usb

вопрос снят. это я что-то в конфиге ядра накосячил.

взял конфиг старого, кое-что подправил - и все заработало

friday ★★★ ()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.