LINUX.ORG.RU
Форум — Linux-hardware  

SATA и R/W multiple sector transfer


0

0

Хотел спросить, имеет ли значение, что: >> R/W multiple sector transfer: Max = 16 Current = 1 Все таки на обычных иде-дисках он всегда 16. Этот диск sata, ядро 2.6.18, драйвер nv_sata (мать Nforce4).

Собстенно, вопрос возник в связи с тем, что поставил dc++ и при расшаривании этого диска он вылетает c сообщением "ошибка шины", а в логах остается примерно следующее:

ata3: EH complete sd 2:0:0:0: SCSI error: return code = 0x08000002 sda: Current: sense key=0x3 ASC=0x11 ASCQ=0x4 end_request: I/O error, dev sda, sector 454359327 ata3: EH complete SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off SCSI device sda: drive cache: write back

Что интересно, DC-QT, например, таких проблем не вызывает, но он и расшаривает не с так напряженно. Вот я и думаю, кто виноват, прога или винт кончается?

anonymous

На всякий случай - hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media Model Number: HDT722525DLA380 Serial Number: VDB41DT4EG7V0C Firmware Revision: V44OA96A Standards: Used: ATA/ATAPI-7 T13 1532D revision 1 Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 488397168 device size with M = 1024*1024: 238475 MBytes device size with M = 1000*1000: 250059 MBytes (250 GB) Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 1 Advanced power management level: unknown setting (0x0000) Recommended acoustic management value: 128, current value: 254 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=240ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * DOWNLOAD_MICROCODE Advanced Power Management feature set Power-Up In Standby feature set SET_FEATURES required to spinup after power up Address Offset Reserved Area Boot SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * WRITE_{DMA|MULTIPLE}_FUA_EXT * 64-bit World wide name * URG for READ_STREAM[_DMA]_EXT * URG for WRITE_STREAM[_DMA]_EXT * SATA-I signaling speed (1.5Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management Non-Zero buffer offsets in DMA Setup FIS DMA Setup Auto-Activate optimization Device-initiated interface power management In-order data delivery * Software settings preservation Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count not supported: enhanced erase 112min for SECURITY ERASE UNIT. Checksum: correct

anonymous
()
Ответ на: комментарий от anonymous

На всякий случай - hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media
Model Number: HDT722525DLA380
Serial Number: VDB41DT4EG7V0C
Firmware Revision: V44OA96A
Standards:
Used: ATA/ATAPI-7 T13 1532D revision 1
Supported: 7 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 488397168
device size with M = 1024*1024: 238475 MBytes
device size with M = 1000*1000: 250059 MBytes (250 GB)
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Advanced power management level: unknown setting (0x0000)
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
Advanced Power Management feature set
Power-Up In Standby feature set
SET_FEATURES required to spinup after power up
Address Offset Reserved Area Boot
SET_MAX security extension
Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* SATA-I signaling speed (1.5Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
112min for SECURITY ERASE UNIT.
Checksum: correct

anonymous
()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.
Linux-hardware