Можно ли исправить ошибки на этом винте?
=== START OF INFORMATION SECTION === Device Model: ST2000DM001-1CH164 Serial Number: Z240NCVS LU WWN Device Id: 5 000c50 0501b3ded Firmware Version: CC26 User Capacity: 2б═000б═398б═934б═016 bytes [2,00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sun Apr 6 11:50:29 2014 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes.
General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3085) SCT Status supported.
SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 208124584 3 Spin_Up_Time 0x0003 094 094 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 85 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 040 030 030 Pre-fail Always In_the_past 21612318557025 9 Power_On_Hours 0x0032 092 092 000 Old_age Always - 7332 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 85 183 Runtime_Bad_Block 0x0032 099 099 000 Old_age Always - 1 184 End-to-End_Error 0x0032 099 099 099 Old_age Always FAILING_NOW 1 187 Reported_Uncorrect 0x0032 089 089 000 Old_age Always - 11 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 072 050 045 Old_age Always - 28 (Min/Max 27/32) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 63 193 Load_Cycle_Count 0x0032 096 096 000 Old_age Always - 9051 194 Temperature_Celsius 0x0022 028 050 000 Old_age Always - 28 (0 14 0 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 234878876523426 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 7363475113 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 59257874110
SMART Error Log Version: 1 ATA Error Count: 23 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It «wraps» after 49.710 days.
Error 23 occurred at disk power-on lifetime: 7321 hours (305 days + 1 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH — -- — -- — -- -- 40 51 00 98 50 04 00 Error: UNC at LBA = 0x00045098 = 282776
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name — -- — -- — -- — -- ---------------- -------------------- 60 00 00 e0 4f 04 40 00 3d+10:26:59.099 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+10:26:59.099 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 3d+10:26:59.099 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 3d+10:26:59.098 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+10:26:59.098 SET FEATURES [Set transfer mode]
Error 22 occurred at disk power-on lifetime: 7321 hours (305 days + 1 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH — -- — -- — -- -- 40 51 00 98 50 04 00 Error: UNC at LBA = 0x00045098 = 282776
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name — -- — -- — -- — -- ---------------- -------------------- 60 00 00 e0 4f 04 40 00 3d+10:26:59.099 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+10:26:59.099 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 3d+10:26:59.099 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 3d+10:26:59.098 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+10:26:59.098 SET FEATURES [Set transfer mode]
Error 21 occurred at disk power-on lifetime: 7321 hours (305 days + 1 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH — -- — -- — -- -- 40 51 00 98 50 04 00 Error: UNC at LBA = 0x00045098 = 282776
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name — -- — -- — -- — -- ---------------- -------------------- 60 00 00 e0 4f 04 40 00 3d+10:26:56.161 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+10:26:56.161 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 3d+10:26:56.161 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 3d+10:26:56.161 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+10:26:56.160 SET FEATURES [Set transfer mode]
Error 20 occurred at disk power-on lifetime: 7321 hours (305 days + 1 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH — -- — -- — -- -- 40 51 00 98 50 04 00 Error: UNC at LBA = 0x00045098 = 282776
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name — -- — -- — -- — -- ---------------- -------------------- 60 00 00 e0 4f 04 40 00 3d+10:26:56.161 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+10:26:56.161 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 3d+10:26:56.161 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 3d+10:26:56.161 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+10:26:56.160 SET FEATURES [Set transfer mode]
Error 19 occurred at disk power-on lifetime: 7321 hours (305 days + 1 hours) When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were: ER ST SC SN CL CH DH — -- — -- — -- -- 40 51 00 98 50 04 00 Error: UNC at LBA = 0x00045098 = 282776
Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name — -- — -- — -- — -- ---------------- -------------------- 60 00 00 e0 4f 04 40 00 3d+10:26:53.248 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 3d+10:26:53.248 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 3d+10:26:53.248 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 3d+10:26:53.247 IDENTIFY DEVICE ef 03 46 00 00 00 a0 00 3d+10:26:53.247 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 7151 - # 2 Extended offline Completed without error 00% 6771 -
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
