LILO - текстовый режим (загрузка Debian в текстовом).

# /etc/lilo.conf  -   systemwide LILO configuration (LILO 23)
# details see in manpages: lilo(8) and lilo.conf(5)

# +-------------------------------------------------------------+
# |                        !! Reminder !!                       |
# |                                                             |
# | Don't forget to run 'lilo' after you make changes to this   |
# | conffile or you have installed a new kernel.                |
# +-------------------------------------------------------------+


# #################### LILO global section ######################

# With all newer systems (until year 2004) you can use the RAM
# above 15 MB. This option allows the use of this range of RAM.
#large-memory

# With all newer systems you can boot from any partition on disks
# with more than 1024 cylinders. This option allows the use of
# partitions above 1024 cylinders.
lba32

# Specifies the boot device.  This is where Lilo installs its boot
# block.  It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
# With newer kernel you should use the ID of the boot device, which
# can be found here: /dev/disks/by-id/ata*.
#boot = /dev/sda
boot = /dev/disk/by-id/ata-WDC_WD3200BEVT-24A23T0_WD-WXE0AC9S8694

# This option may be needed for some software RAID installs.
#raid-extra-boot = mbr-only

# Enable map compaction.  This tries to merge read requests for
# adjacent sectors into a single read request. This drastically
# reduces load time and keeps the map smaller.  Using 'compact'
# is especially recommended when booting from a floppy disk.
# It is disabled here by default because it doesn't always work.
#compact

# Set the verbose level for bootloader installation. Value range:
# 0 to 5. Default value is 0.
#verbose = 1

# Specifies the location of the map file. Lilo creates the (sector)
# map file of direct sector addresses which are independent of any
# filesystem.
map = /boot/map

# ---------------------------------------------------------------

# Specifies the menu interface. You have the choice between:
#   text: simple text menu with black background and white text
#   menu: configurable text menu with background and text colors.
#   bmp:  graphical menu with 640x480 bitmap background.
install = text

# A) Customized boot message for choice 'text'.
# For the simple text menu you can set an extra message in the
# created file. Its text will be displayed before boot prompt.
message = /boot/message.txt

# B) Configuration of the scheme for choice 'menu'.
# Use following coding: <text>:<highlight>:<border>:<title>
# The first character of each part sets the text frontcolor,
# the second character of earch part sets the text backcolor,
# an upper-case character sets bold face text (frontcolor).
# i.g. 'menu-scheme=wm:rw:wm:Wm'. Possible colors:
# k=black, b=blue, g=green, c=cyan, r=red, m=magenta, y=yellow, w=white.
#menu-scheme = Wb:Yr:Wb:Wb
#menu-title = " DESDEMONA Boot-Manager "

# C) Configuration of the image for choice 'bmp'.
# For the graphical menu you need a bitmap file, which needs a special
# menu configuration in the file header (see: lilo -E). Ideally you
# use one of the delivered images of the lilo package.
#   with 16 colors:    onlyblue, tuxlogo, inside
#   with 256 colors:   coffee
#   for Debian:        debianlilo, debian, debian-de
#bitmap = /boot/tuxlogo.bmp

# ---------------------------------------------------------------

# Specifies the number of deciseconds (0.1 seconds) how long LILO
# should wait before booting the first image.  LILO doesn't wait if
# 'delay' is omitted or set to zero. You do not see the defined menu.
delay = 600

# Prompt to start one certain kernel from the displayed menu.
# It is very recommeded to also set 'timeout'. Without timeout boot
# will not take place unless you hit return. Timeout is the number
# of deciseconds (0.1 seconds) after there the default image will
# be started. With 'single-key' alias numbers for each menu line can
# be used.
prompt
timeout = 100
#single-key

# ---------------------------------------------------------------

# Specifying the VGA text mode that should be selected when booting.
# The following values are recognized (case is ignored):
#   vga=normal    80x25 text mode (default)
#   vga=extended  80x50 text mode (abbreviated to 'ext')
#   vga=ask       stop and ask for user input: choice of text mode
#   vga=<mode>    use the corresponding text mode number. A list of
#                   available modes can be obtained by booting with
#                   vga=ask'  and then pressing [Enter].
# Another way is the use of frame buffer mode. Then the kernel
# will switch from the normal vga text mode (80x25) to the frame
# buffer mode (if frame buffer support is in the kernel):
#   vga=0x314      800x600 @ 16 bit
#   vga=0x317     1024x768 @ 16 bit
#   vga=0x318     1024x768 @ 24 bit
#vga = ask
vga = normal
#vga = 0x317

# ---------------------------------------------------------------

# Kernel command line options that apply to all installed images go
# here.  See 'kernel-parameters.txt' in the Linux kernel 'Documentation'
# directory. I.g. for start into 'init 5' write:  append="5"
#append = ""

# If you used a serial console to install Debian, this option should be
# enabled by default.
#serial = 0,9600

# Set the image which should be started after delay or timeout.
# If not set, the first defined image will be started.
#default = linux-3.12.1


# ################### LILO per-image section ####################
# Each image is configured with the linux kernel (=image) and
# usually with the initrd file. Configure all GNU/Linux systems
# on other partitions, too.

image = /boot/vmlinuz-3.13.4
        label = "linux-3.13.4"
        #root = /dev/sda2
        root = "UUID=fb61f516-26ae-4a4a-ad49-2ae0df139152"
        read-only
#       restricted
#       alias = 1
#       optional
        initrd = /boot/initrd.img-3.13.4

image = /boot/vmlinuz-3.12-1-686-pae
        label = "linux-3.12.1"
        #root = /dev/sda2
        root = "UUID=fb61f516-26ae-4a4a-ad49-2ae0df139152"
        read-only
#       restricted
#       alias = 2
#       optional
        initrd = /boot/initrd.img-3.12-1-686-pae