В локалке на прокси админ забанил сайт. Народ из локалки хочет смотреть забаненный сайт и поэтому ищет список анонимных проксей в инете. Есть некий, нахоящийся рядом сервак, на котором есть админ, которого завут vilfred. Вобщем, каким образом при помощи iptables поднять анонимный прокси только для одного ip-адреса так чтобы он разрешал ходить только на один www.linux.org.ru? По каким ключевым словам искать? squid ради этого ставить - не катит, т.к. удаленный сервер p100, 32RAM и так еле еле. На удаленном сервере iptables настроены так, чтобы он еще и держал небольшую локальную сетку следующим образом: #!/bin/sh INET_IP="123.45.67.12" INET_IFACE="eth0" INET_BROADCAST="123.45.67.255" # 1.2 Local Area Network configuration. # # your LAN's IP range and localhost IP. /24 means to only use the first 24 # bits of the 32 bit IP address. the same as netmask 255.255.255.0 # LAN_IP="10.0.0.1" LAN_IP_RANGE="10.0.0.0/24" LAN_IFACE="eth1" # # 1.4 Localhost Configuration. # LO_IFACE="lo" LO_IP="127.0.0.1" # # 1.5 IPTables Configuration. # IPTABLES="/sbin/iptables" # # 1.6 Other Configuration. # ########################################################################### # # 2. Module loading. # # # Needed to initially load modules # /sbin/depmod -a # # 2.1 Required modules # /sbin/modprobe ip_tables /sbin/modprobe ip_conntrack /sbin/modprobe iptable_filter /sbin/modprobe iptable_mangle /sbin/modprobe iptable_nat /sbin/modprobe ipt_LOG /sbin/modprobe ipt_limit /sbin/modprobe ipt_state # # 2.2 Non-Required modules # #/sbin/modprobe ipt_owner #/sbin/modprobe ipt_REJECT #/sbin/modprobe ipt_MASQUERADE #/sbin/modprobe ip_conntrack_ftp #/sbin/modprobe ip_conntrack_irc #/sbin/modprobe ip_nat_ftp #/sbin/modprobe ip_nat_irc ########################################################################### # # 3. /proc set up. # # # 3.1 Required proc configuration # echo "1" > /proc/sys/net/ipv4/ip_forward # # 3.2 Non-Required proc configuration # #echo "1" > /proc/sys/net/ipv4/conf/all/rp_filter #echo "1" > /proc/sys/net/ipv4/conf/all/proxy_arp #echo "1" > /proc/sys/net/ipv4/ip_dynaddr ########################################################################### # # 4. rules set up. # ###### # 4.1 Filter table # # # 4.1.1 Set policies # $IPTABLES -P INPUT DROP $IPTABLES -P OUTPUT DROP $IPTABLES -P FORWARD DROP # # 4.1.2 Create userspecified chains # # # Create chain for bad tcp packets # $IPTABLES -N bad_tcp_packets # # Create separate chains for ICMP, TCP and UDP to traverse # $IPTABLES -N allowed $IPTABLES -N tcp_packets $IPTABLES -N udp_packets $IPTABLES -N icmp_packets # # 4.1.3 Create content in userspecified chains # # # bad_tcp_packets chain # $IPTABLES -A bad_tcp_packets -p tcp --tcp-flags SYN,ACK SYN,ACK \ -m state --state NEW -j REJECT --reject-with tcp-reset $IPTABLES -A bad_tcp_packets -p tcp ! --syn -m state --state NEW -j LOG \ --log-prefix "New not syn:" $IPTABLES -A bad_tcp_packets -p tcp ! --syn -m state --state NEW -j DROP # # allowed chain # $IPTABLES -A allowed -p TCP --syn -j ACCEPT $IPTABLES -A allowed -p TCP -m state --state ESTABLISHED,RELATED -j ACCEPT $IPTABLES -A allowed -p TCP -j DROP # # TCP rules # $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 21 -j allowed $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 22 -j allowed $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 80 -j allowed $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 8080 -j allowed $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 8081 -j allowed $IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 113 -j allowed # # UDP ports # $IPTABLES -A udp_packets -p UDP -s 0/0 --destination-port 53 -j ACCEPT $IPTABLES -A udp_packets -p UDP -s 0/0 --destination-port 123 -j ACCEPT $IPTABLES -A udp_packets -p UDP -s 0/0 --destination-port 2074 -j ACCEPT $IPTABLES -A udp_packets -p UDP -s 0/0 --destination-port 4000 -j ACCEPT # # In Microsoft Networks you will be swamped by broadcasts. These lines # will prevent them from showing up in the logs. # $IPTABLES -A udp_packets -p UDP -i $INET_IFACE -d $INET_BROADCAST \ --destination-port 135:139 -j DROP # # If we get DHCP requests from the Outside of our network, our logs will # be swamped as well. This rule will block them from getting logged. # #$IPTABLES -A udp_packets -p UDP -i $INET_IFACE -d 255.255.255.255 \ #--destination-port 67:68 -j DROP # # ICMP rules # $IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 8 -j ACCEPT $IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 11 -j ACCEPT # # 4.1.4 INPUT chain # # # Bad TCP packets we don't want. # $IPTABLES -A INPUT -p tcp -j bad_tcp_packets # # Rules for special networks not part of the Internet # $IPTABLES -A INPUT -p ALL -i $LAN_IFACE -s $LAN_IP_RANGE -j ACCEPT $IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $LO_IP -j ACCEPT $IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $LAN_IP -j ACCEPT $IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $INET_IP -j ACCEPT # # Special rule for DHCP requests from LAN, which are not caught properly # otherwise. # $IPTABLES -A INPUT -p UDP -i $LAN_IFACE --dport 67 --sport 68 -j ACCEPT # # Rules for incoming packets from the internet. # $IPTABLES -A INPUT -p ALL -d $INET_IP -m state --state ESTABLISHED,RELATED \ -j ACCEPT $IPTABLES -A INPUT -p TCP -i $INET_IFACE -j tcp_packets $IPTABLES -A INPUT -p UDP -i $INET_IFACE -j udp_packets $IPTABLES -A INPUT -p ICMP -i $INET_IFACE -j icmp_packets # # If you have a Microsoft Network on the outside of your firewall, you may # also get flooded by Multicasts. We drop them so we do not get flooded by # logs # #$IPTABLES -A INPUT -i $INET_IFACE -d 224.0.0.0/8 -j DROP # # Log weird packets that don't match the above. # $IPTABLES -A INPUT -m limit --limit 3/minute --limit-burst 3 -j LOG \ --log-level DEBUG --log-prefix "IPT INPUT packet died: " # # 4.1.5 FORWARD chain # # # Bad TCP packets we don't want # $IPTABLES -A FORWARD -p tcp -j bad_tcp_packets # # Accept the packets we actually want to forward # $IPTABLES -A FORWARD -i $LAN_IFACE -j ACCEPT $IPTABLES -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT # # Log weird packets that don't match the above. # $IPTABLES -A FORWARD -m limit --limit 3/minute --limit-burst 3 -j LOG \ --log-level DEBUG --log-prefix "IPT FORWARD packet died: " # # 4.1.6 OUTPUT chain # # # Bad TCP packets we don't want. # $IPTABLES -A OUTPUT -p tcp -j bad_tcp_packets # # Special OUTPUT rules to decide which IP's to allow. # $IPTABLES -A OUTPUT -p ALL -s $LO_IP -j ACCEPT $IPTABLES -A OUTPUT -p ALL -s $LAN_IP -j ACCEPT $IPTABLES -A OUTPUT -p ALL -s $INET_IP -j ACCEPT # # Log weird packets that don't match the above. # $IPTABLES -A OUTPUT -m limit --limit 3/minute --limit-burst 3 -j LOG \ --log-level DEBUG --log-prefix "IPT OUTPUT packet died: " ###### # 4.2 nat table # # # 4.2.1 Set policies # # # 4.2.2 Create user specified chains # # # 4.2.3 Create content in user specified chains # # # 4.2.4 PREROUTING chain # # # 4.2.5 POSTROUTING chain # # # Enable simple IP Forwarding and Network Address Translation # $IPTABLES -t nat -A POSTROUTING -o $INET_IFACE -j SNAT --to-source $INET_IP # # 4.2.6 OUTPUT chain # ###### # 4.3 mangle table # # # 4.3.1 Set policies # # # 4.3.2 Create user specified chains # # # 4.3.3 Create content in user specified chains # # # 4.3.4 PREROUTING chain # # # 4.3.5 INPUT chain # # # 4.3.6 FORWARD chain # # # 4.3.7 OUTPUT chain # # # 4.3.8 POSTROUTING chain # # переслать входящие UDP пакеты(порт 5060 и 16500) на интерфейс eth0 (X.X.X.X) # во внутреннюю сеть на 172.16.0.200 на соответствующие порты # iptables -t nat -A PREROUTING -p udp -d x.x.x.x --dport 5060 -j DNAT --to-destination 172.16.0.200 # iptables -t nat -A PREROUTING -p udp -d x.x.x.x --dport 16500 -j DNAT --to-destination 172.16.0.200 #
Ответ на:
комментарий
от vilfred
Ответ на:
комментарий
от HAW
Ответ на:
комментарий
от vilfred
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.