LINUX.ORG.RU
ФорумAdmin

Потерялся eth


0

1

В машину вставлено 3 сетевые карты

  • Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller 2 порта (встроенный)
  • Intel Corporation 82576 Gigabit Network Connection 4 порта (PCI)
  • D-Link System Inc Device 4a01 (PCI)
# lspci
............
07:00.0 Ethernet controller: Intel Corporation 82576 Gigabit Network Connection (rev 01)
07:00.1 Ethernet controller: Intel Corporation 82576 Gigabit Network Connection (rev 01)
08:00.0 Ethernet controller: Intel Corporation 82576 Gigabit Network Connection (rev 01)
08:00.1 Ethernet controller: Intel Corporation 82576 Gigabit Network Connection (rev 01)
09:00.0 RAID bus controller: Marvell Technology Group Ltd. 88SE6440 SAS/SATA PCIe controller (rev 02)
0a:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6121 SATA II Controller (rev b2)
0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
0c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
0e:00.0 Ethernet controller: D-Link System Inc Device 4a01 (rev 11)
.....

Всего 7 интерфейсов, но находятся только 6 (2 встроенных и 4 Intel) куда пропал Dlink, как я понимаю eth6?

# ifconfig -a
bond0     Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          inet addr:10.10.10.1  Bcast:10.10.10.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

br0       Link encap:Ethernet  HWaddr 20:cf:30:e2:ab:05
          inet addr:192.168.201.6  Bcast:192.168.201.155  Mask:255.255.255.0
          inet6 addr: fe80::22cf:30ff:fee2:ab05/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:9087 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6541 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4274881 (4.2 MB)  TX bytes:883753 (883.7 KB)

eth0      Link encap:Ethernet  HWaddr 20:cf:30:e2:ab:05
          inet6 addr: fe80::22cf:30ff:fee2:ab05/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:13912 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7821 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:5013283 (5.0 MB)  TX bytes:1031509 (1.0 MB)
          Interrupt:83 Base address:0x2000

eth1      Link encap:Ethernet  HWaddr 20:cf:30:e2:8f:46
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:84 Base address:0xa000

eth2      Link encap:Ethernet  HWaddr 00:1b:21:7f:c6:24
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Память:fafa0000-fafc0000

eth3      Link encap:Ethernet  HWaddr 00:1b:21:7f:c6:25
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Память:fafe0000-fb000000

eth4      Link encap:Ethernet  HWaddr 00:1b:21:7f:c6:26
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Память:fb9a0000-fb9c0000

eth5      Link encap:Ethernet  HWaddr 00:1b:21:7f:c6:27
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Память:fb9e0000-fba00000

lo        Link encap:Локальная петля (Loopback)
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:129 errors:0 dropped:0 overruns:0 frame:0
          TX packets:129 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:14906 (14.9 KB)  TX bytes:14906 (14.9 KB)

virbr0    Link encap:Ethernet  HWaddr 56:c6:66:ca:90:d2
          inet addr:192.168.122.1  Bcast:192.168.122.255  Mask:255.255.255.0
          inet6 addr: fe80::54c6:66ff:feca:90d2/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:468 (468.0 B)

Возможно Linux не смог драйвер найти, поэтому устройства нет? Подскажите, как мне найти этот интерфейс?

★★★★★

Собрать модуль для этого устройства.

CTAPK ()
Ответ на: комментарий от uspen
0e:00.0 Ethernet controller: D-Link System Inc Device 4a01 (rev 11)
        Subsystem: D-Link System Inc Device 4a01
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx-
        Latency: 64 (5750ns min, 7500ns max), Cache Line Size: 256 bytes
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at fbe00000 (32-bit, non-prefetchable) [size=16K]
        Region 1: I/O ports at e000 [size=256]
        Expansion ROM at c0800000 [disabled] [size=128K]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] Vital Product Data
                Product Name: D
                Unknown small resource type 08, will not decode more.

да как понимаю по аналогии с другим адаптером то что-то не так

0c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
        Subsystem: ASUSTeK Computer Inc. Device 8367
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 256 bytes
        Interrupt: pin A routed to IRQ 83
        Region 0: I/O ports at d800 [size=256]
        Region 2: Memory at fbdff000 (64-bit, non-prefetchable) [size=4K]
        Region 4: Memory at f4ef0000 (64-bit, prefetchable) [size=64K]
        Expansion ROM at fbdc0000 [disabled] [size=128K]
        Capabilities: [40] Power Management version 3
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
                Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee01000  Data: 40ab
        Capabilities: [70] Express (v1) Endpoint, MSI 01
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <8us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <64us
                        ClockPM+ Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        Capabilities: [b0] MSI-X: Enable- Count=2 Masked-
                Vector table: BAR=4 offset=00000000
                PBA: BAR=4 offset=00000800
        Capabilities: [d0] Vital Product Data
                Unknown small resource type 05, will not decode more.
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                CEMsk:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [140 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Capabilities: [160 v1] Device Serial Number 00-00-00-00-ec-10-68-81
        Kernel driver in use: r8169
        Kernel modules: r8169

Не подскажите путь как собрать этот модуль, хотя бы точку от куда копать.

petav ★★★★★ ()

petav> D-Link System Inc Device 4a01 (PCI)

Дешевле и быстрее будет заменить это на что-то нормальное.

sdio ★★★★★ ()
Ответ на: комментарий от petav

По модели карты посмотри в гугле и длинке, да сюда сообщи модель. dmesg, тоже не помешало бы. А там и модуль соберешь.

uspen ★★★★★ ()
Ответ на: комментарий от AITap

Покажите, что говорит lspci -n.

# lspci -n
00:00.0 0600: 8086:3405 (rev 13)
00:01.0 0604: 8086:3408 (rev 13)
00:03.0 0604: 8086:340a (rev 13)
00:07.0 0604: 8086:340e (rev 13)
00:14.0 0800: 8086:342e (rev 13)
00:14.1 0800: 8086:3422 (rev 13)
00:14.2 0800: 8086:3423 (rev 13)
00:14.3 0800: 8086:3438 (rev 13)
00:1a.0 0c03: 8086:3a37
00:1a.1 0c03: 8086:3a38
00:1a.2 0c03: 8086:3a39
00:1a.7 0c03: 8086:3a3c
00:1b.0 0403: 8086:3a3e
00:1c.0 0604: 8086:3a40
00:1c.1 0604: 8086:3a42
00:1c.2 0604: 8086:3a44
00:1c.3 0604: 8086:3a46
00:1c.4 0604: 8086:3a48
00:1d.0 0c03: 8086:3a34
00:1d.1 0c03: 8086:3a35
00:1d.2 0c03: 8086:3a36
00:1d.7 0c03: 8086:3a3a
00:1e.0 0604: 8086:244e (rev 90)
00:1f.0 0601: 8086:3a16
00:1f.2 0101: 8086:3a20
00:1f.3 0c05: 8086:3a30
00:1f.5 0101: 8086:3a26
01:00.0 0604: 1033:0125 (rev 06)
01:00.1 0604: 1033:0125 (rev 06)
04:00.0 0300: 10de:06e4 (rev a1)
05:00.0 0604: 111d:8018 (rev 0e)
06:02.0 0604: 111d:8018 (rev 0e)
06:04.0 0604: 111d:8018 (rev 0e)
07:00.0 0200: 8086:10e8 (rev 01)
07:00.1 0200: 8086:10e8 (rev 01)
08:00.0 0200: 8086:10e8 (rev 01)
08:00.1 0200: 8086:10e8 (rev 01)
09:00.0 0104: 11ab:6440 (rev 02)
0a:00.0 0101: 11ab:6121 (rev b2)
0b:00.0 0200: 10ec:8168 (rev 02)
0c:00.0 0200: 10ec:8168 (rev 02)
0e:00.0 0200: 1186:4a01 (rev 11)
0e:04.0 0c00: 11c1:5811 (rev 70)
ff:00.0 0600: 8086:2c41 (rev 05)
ff:00.1 0600: 8086:2c01 (rev 05)
ff:02.0 0600: 8086:2c10 (rev 05)
ff:02.1 0600: 8086:2c11 (rev 05)
ff:03.0 0600: 8086:2c18 (rev 05)
ff:03.1 0600: 8086:2c19 (rev 05)
ff:03.4 0600: 8086:2c1c (rev 05)
ff:04.0 0600: 8086:2c20 (rev 05)
ff:04.1 0600: 8086:2c21 (rev 05)
ff:04.2 0600: 8086:2c22 (rev 05)
ff:04.3 0600: 8086:2c23 (rev 05)
ff:05.0 0600: 8086:2c28 (rev 05)
ff:05.1 0600: 8086:2c29 (rev 05)
ff:05.2 0600: 8086:2c2a (rev 05)
ff:05.3 0600: 8086:2c2b (rev 05)
ff:06.0 0600: 8086:2c30 (rev 05)
ff:06.1 0600: 8086:2c31 (rev 05)
ff:06.2 0600: 8086:2c32 (rev 05)
ff:06.3 0600: 8086:2c33 (rev 05)
petav ★★★★★ ()
Ответ на: комментарий от uspen

По модели карты посмотри в гугле и длинке, да сюда сообщи модель.

D-Link <DGE-530T> Адаптер сетевой PCI 10/100/1000Mbps (32бит)

dmesg, тоже не помешало бы

Там такой вывод длинный что понять не могу какую информацию показать

А там и модуль соберешь

Уже ищу информацию как.

petav ★★★★★ ()
Ответ на: комментарий от AITap

А что будет, если сделать update-pciids?

тоже самое, ни чего не изменилось

b# update-pciids
Downloaded daily snapshot dated 2011-02-06 03:15:03
root@adam:/home/variantb# lspci -n
00:00.0 0600: 8086:3405 (rev 13)
00:01.0 0604: 8086:3408 (rev 13)
00:03.0 0604: 8086:340a (rev 13)
00:07.0 0604: 8086:340e (rev 13)
00:14.0 0800: 8086:342e (rev 13)
00:14.1 0800: 8086:3422 (rev 13)
00:14.2 0800: 8086:3423 (rev 13)
00:14.3 0800: 8086:3438 (rev 13)
00:1a.0 0c03: 8086:3a37
00:1a.1 0c03: 8086:3a38
00:1a.2 0c03: 8086:3a39
00:1a.7 0c03: 8086:3a3c
00:1b.0 0403: 8086:3a3e
00:1c.0 0604: 8086:3a40
00:1c.1 0604: 8086:3a42
00:1c.2 0604: 8086:3a44
00:1c.3 0604: 8086:3a46
00:1c.4 0604: 8086:3a48
00:1d.0 0c03: 8086:3a34
00:1d.1 0c03: 8086:3a35
00:1d.2 0c03: 8086:3a36
00:1d.7 0c03: 8086:3a3a
00:1e.0 0604: 8086:244e (rev 90)
00:1f.0 0601: 8086:3a16
00:1f.2 0101: 8086:3a20
00:1f.3 0c05: 8086:3a30
00:1f.5 0101: 8086:3a26
01:00.0 0604: 1033:0125 (rev 06)
01:00.1 0604: 1033:0125 (rev 06)
04:00.0 0300: 10de:06e4 (rev a1)
05:00.0 0604: 111d:8018 (rev 0e)
06:02.0 0604: 111d:8018 (rev 0e)
06:04.0 0604: 111d:8018 (rev 0e)
07:00.0 0200: 8086:10e8 (rev 01)
07:00.1 0200: 8086:10e8 (rev 01)
08:00.0 0200: 8086:10e8 (rev 01)
08:00.1 0200: 8086:10e8 (rev 01)
09:00.0 0104: 11ab:6440 (rev 02)
0a:00.0 0101: 11ab:6121 (rev b2)
0b:00.0 0200: 10ec:8168 (rev 02)
0c:00.0 0200: 10ec:8168 (rev 02)
0e:00.0 0200: 1186:4a01 (rev 11)
0e:04.0 0c00: 11c1:5811 (rev 70)
ff:00.0 0600: 8086:2c41 (rev 05)
ff:00.1 0600: 8086:2c01 (rev 05)
ff:02.0 0600: 8086:2c10 (rev 05)
ff:02.1 0600: 8086:2c11 (rev 05)
ff:03.0 0600: 8086:2c18 (rev 05)
ff:03.1 0600: 8086:2c19 (rev 05)
ff:03.4 0600: 8086:2c1c (rev 05)
ff:04.0 0600: 8086:2c20 (rev 05)
ff:04.1 0600: 8086:2c21 (rev 05)
ff:04.2 0600: 8086:2c22 (rev 05)
ff:04.3 0600: 8086:2c23 (rev 05)
ff:05.0 0600: 8086:2c28 (rev 05)
ff:05.1 0600: 8086:2c29 (rev 05)
ff:05.2 0600: 8086:2c2a (rev 05)
ff:05.3 0600: 8086:2c2b (rev 05)
ff:06.0 0600: 8086:2c30 (rev 05)
ff:06.1 0600: 8086:2c31 (rev 05)
ff:06.2 0600: 8086:2c32 (rev 05)
ff:06.3 0600: 8086:2c33 (rev 05)

Нашел статью по установке этой карты в Ubuntu.

petav ★★★★★ ()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.