LINUX.ORG.RU
решено ФорумAdmin

Не работает WiFi (Ralink RT5390) в Gentoo

 ,


0

1

Всем привет, поставил Gentoo (версия ядра linux 4.0.5) на ноут с Ralink RT5390, при настройке ядра вроде бы всё указал, прошивки вообще для всего (тупо поставил linux-firmware) есть, но:

wakoo@redsovok ~ $ sudo iwconfig wlp2s0
wlp2s0 no wireless extensions.
wakoo@redsovok ~ $ sudo iw dev wlp2s0 info
Interface wlp2s0
ifindex 3
wdev 0x1
addr 84:4b:f5:a4:08:a7
type managed
wiphy 0
wakoo@redsovok ~ $ sudo iw phy phy0 info
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports RSN-IBSS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP (00-0f-ac:4)
* 00-0f-ac:10
* GCMP (00-0f-ac:8)
* 00-0f-ac:9
Available Antennas: TX 0 RX 0
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* WDS
* monitor
Band 1:
Capabilities: 0x172
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-7, 32
TX unequal modulation not supported
HT TX Max spatial streams: 1
HT TX MCS rate indexes supported may differ
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm) (no IR)
* 2484 MHz [14] (20.0 dBm) (no IR)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* set_wds_peer
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* Unknown command (104)
* connect
* disconnect
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ AP } <= 8,
total <= 8, #channels <= 1
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports low priority scan.
Device supports scan flush.
Device supports AP scan.
Device supports per-vif TX power setting
Driver supports a userspace MPM
wakoo@redsovok ~ $ dmesg | grep 80211
[ 0.776601] cfg80211: Calling CRDA to update world regulatory domain
[ 1.315807] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5390, rev 1502 detected
[ 1.319470] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5390 detected
[ 1.319553] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.896498] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 18.923513] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.34
wakoo@redsovok ~ $ dmesg | grep wlan
[ 11.630328] rt2800pci 0000:02:00.0 wlp2s0: renamed from wlan0
[ 11.635859] systemd-udevd[2652]: renamed network interface wlan0 to wlp2s0
wakoo@redsovok ~ $ dmesg | grep wlp2s0
[ 11.630328] rt2800pci 0000:02:00.0 wlp2s0: renamed from wlan0
[ 11.635859] systemd-udevd[2652]: renamed network interface wlan0 to wlp2s0
[ 19.017345] IPv6: ADDRCONF(NETDEV_UP): wlp2s0: link is not ready



Последнее исправление: watashinoshi (всего исправлений: 1)

no wireless extensions

CONFIG_CFG80211_WEXT
Networking support --> Wireless --> cfg80211 - wireless configuration API --> cfg80211 wireless extensions compability (включить)
DeadEye ★★★★★
()

Да, кстати, оберни из [quote] в [code].

DeadEye ★★★★★
()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.