LINUX.ORG.RU

Сообщения DeeZ

 

Transmission на NAS (ARM)

На NAS установил Transmission, после чего в сислог посыпались следующие сообщения:

Nov 14 01:24:17 axentraserver kernel: Alignment trap: not handling swp instruction
Nov 14 01:24:17 axentraserver kernel: Alignment trap: not handling instruction e1043090 at [<4039aa0c>]
Nov 14 01:24:17 axentraserver kernel: Unhandled fault: alignment exception (0x801) at 0x464c457f

Если остановить демон - ошибки прекращаются.
1. что это?
2. это смертельно для NAS?
3. Это можно исправить?

На сколько я пока успел разобраться - это ошибки при компилировании трансмишина. Как подсказали Linux@jabber.ru «АРМ не умеет выполнять команды по не выровненому адресу».

DeeZ
()
11 комментариев

Сдохла флешка

Сдохла флешка, eeePC T91, флешка дохнет не первый раз. Раньше просто форматировал, а сейчас не на всех компах видится. При подключении к машине с Debian в dmesg куча ошибок.

Как оживить? желательно без форматирования, можно как то таблицу разделов восстановить? или только форматировать? или это вообще уже смерть?

[   82.333858] USB Mass Storage support registered.
[   82.338030] usb-storage: device found at 2
[   82.338037] usb-storage: waiting for device to settle before scanning
[   87.337530] usb-storage: device scan complete
[   87.344418] scsi 0:0:0:0: Direct-Access     Generic  USB SD Reader    1.00 PQ: 0 ANSI: 0
[   87.351477] scsi 0:0:0:1: Direct-Access     Generic  USB CF Reader    1.01 PQ: 0 ANSI: 0
[   87.358398] scsi 0:0:0:2: Direct-Access     Generic  USB SM Reader    1.02 PQ: 0 ANSI: 0
[   87.365484] scsi 0:0:0:3: Direct-Access     Generic  USB MS Reader    1.03 PQ: 0 ANSI: 0
[   87.583786] Driver 'sd' needs updating - please use bus_type methods
[   87.593635] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   87.604639] sd 0:0:0:1: [sdb] Attached SCSI removable disk
[   87.615623] sd 0:0:0:2: [sdc] Attached SCSI removable disk
[   87.626627] sd 0:0:0:3: [sdd] Attached SCSI removable disk
[  178.264318] sd 0:0:0:0: [sda] 14381056 512-byte hardware sectors (7363 MB)
[  178.277137] sd 0:0:0:0: [sda] Write Protect is off
[  178.277137] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[  178.277137] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  178.298648] sd 0:0:0:0: [sda] 14381056 512-byte hardware sectors (7363 MB)
[  178.312023] sd 0:0:0:0: [sda] Write Protect is off
[  178.312023] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[  178.312023] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  178.312023]  sda:<6>sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  179.350062] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  179.350062] end_request: I/O error, dev sda, sector 0
[  179.350062] Buffer I/O error on device sda, logical block 0
[  180.387397] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  180.387397] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  180.387397] end_request: I/O error, dev sda, sector 0
[  180.388060] Buffer I/O error on device sda, logical block 0
[  181.425205] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  181.425205] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  181.425205] end_request: I/O error, dev sda, sector 0
[  181.425205] Buffer I/O error on device sda, logical block 0
[  182.463039] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  182.463039] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  182.463039] end_request: I/O error, dev sda, sector 0
[  182.463039] Buffer I/O error on device sda, logical block 0
[  183.500877] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  183.500877] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  183.500877] end_request: I/O error, dev sda, sector 0
[  183.500877] Buffer I/O error on device sda, logical block 0
[  183.500877] ldm_validate_partition_table(): Disk read failed.
[  184.538920] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  184.538920] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  184.538920] end_request: I/O error, dev sda, sector 0
[  184.538920] Buffer I/O error on device sda, logical block 0
[  185.577038] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  185.577038] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  185.577038] end_request: I/O error, dev sda, sector 0
[  185.577038] Buffer I/O error on device sda, logical block 0
[  186.614330] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  186.614330] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  186.614330] end_request: I/O error, dev sda, sector 0
[  186.614330] Buffer I/O error on device sda, logical block 0
[  187.652166] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  187.652166] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  187.652166] end_request: I/O error, dev sda, sector 0
[  187.652166] Buffer I/O error on device sda, logical block 0
[  187.652166] Dev sda: unable to read RDB block 0
[  188.690301] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  188.690301] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  188.690301] end_request: I/O error, dev sda, sector 0
[  188.690301] Buffer I/O error on device sda, logical block 0
[  189.727943] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  189.727943] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  189.727943] end_request: I/O error, dev sda, sector 0
[  189.727943] Buffer I/O error on device sda, logical block 0
[  190.765974] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  190.765974] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  190.765974] end_request: I/O error, dev sda, sector 24
[  190.765974] Buffer I/O error on device sda, logical block 3
[  191.804027] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  191.804027] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  191.804027] end_request: I/O error, dev sda, sector 24
[  192.841307] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  192.841307] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  192.841307] end_request: I/O error, dev sda, sector 0
[  192.841307]  unable to read partition table
[  193.879129] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  193.879129] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  193.879129] end_request: I/O error, dev sda, sector 0
[  193.879129] FAT: unable to read boot sector
[  220.965011] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  220.965011] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  220.965011] end_request: I/O error, dev sda, sector 0
[  220.965011] FAT: unable to read boot sector
[  233.076601] sd 0:0:0:0: [sda] Device not ready: Sense Key : Not Ready [current]
[  233.076601] sd 0:0:0:0: [sda] Device not ready: <<vendor>> ASC=0xff ASCQ=0xffASC=0xff <<vendor>> ASCQ=0xff
[  233.076601] end_request: I/O error, dev sda, sector 0
[  233.076601] FAT: unable to read boot sector
[  323.964434] usb 2-1: USB disconnect, address 2
DeeZ
()
11 комментариев

Install SUNWxvnc on Solaris

Прошу помогите немного, в какую сторону копать?
нужно установить SUNWxvnc, есть Solaris (не OpenSolaris).

# pkginfo | grep vnc
system SUNWvncviewer VNC viewer client
system SUNWxvnc X11/VNC server

# pkgadd SUNWxvnc
pkgadd: ERROR: no packages were found in </var/spool/pkg>


как я понимаю - не прописаны репозитории. что странно, я привык что в дебиане все есть. уверен что просто я не туда копаю. усложняется все отсутствием манов =(

# man pkgadd
No manual entry for pkgadd.

# uname -a
SunOS Solaris 5.10 Generic_139556-08 i86pc i386 i86pc



DeeZ
()
9 комментариев

VLC + Xorg (без менеджеров окон)

Возможно ли установить иксы но в качестве менеджера окон постаивть vlc?
что то даже придумать не могу в какую сторону гуглить, ничего не находится
про geexbox и mythbuntu в курсе, но хочется разобраться и настроить самому.

DeeZ
()
7 комментариев

Debian Lenny проблема с Xorg

Помогите разобраться, или подскажите хороший ман, а то не пойму как заставить работать иксы. 

Linux TosDD 2.6.26-2-686 #1 SMP Wed Aug 19 06:06:52 UTC 2009 i686 GNU/Linux
стоит видяха Tridnt: 
01:00.0 VGA compatible controller: Trident Microsystems Cyber 9525 (rev 49)

Вот 2 конфига: первый, тот что сейчас в Debian, с ним X не стартует, идут полосы и все тупит. Второй - конфиг из Puppy, где иксы нормально стартуют и работают. Если конфиг из puppy подсунуть Debian-y - стартуют иксы, но глючат и показывают картинку из последней сессии Puppy (!?!), ощущение что видеопамять не очищается.

# xorg.conf (X.Org X Window System server configuration file)
#
# This file was generated by dexconf, the Debian X Configuration tool, using
# values from the debconf database.
#
# Edit this file with caution, and see the xorg.conf manual page.
# (Type "man xorg.conf" at the shell prompt.)
#
# This file is automatically updated on xserver-xorg package upgrades *only*
# if it has not been modified since the last upgrade of the xserver-xorg
# package.
#
# If you have edited this file but would like it to be automatically updated
# again, run the following command:
#   sudo dpkg-reconfigure -phigh xserver-xorg

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"us,ru"
	Option		"XkbOptions"	"grp:alt_shift_toggle"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
EndSection

Section "Device"
	Identifier	"Configured Video Device"
EndSection

Section "Monitor"
	Identifier	"Configured Monitor"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Monitor		"Configured Monitor"
EndSection

Конфиг из Puppy: 

#Special base config file used in Puppy Linux.

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"  	# Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
    Load        "freetype"

# This loads xtrap extension, used by xrandr
    Load       "xtrap"

# This loads the GLX module (if present)
    Load       "glx"

# This loads dri module (if present)
    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    #RgbPath	"/usr/X11R7/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)

    #FontPath   "/usr/X11R7/lib/X11/fonts/misc/"
    #FontPath   "/usr/X11R7/lib/X11/fonts/Type1/"
    #FontPath   "/usr/X11R7/lib/X11/fonts/TTF/"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Enables mode switching with xrandr
# There is a report that this can cause Xorg not to work on some
# video hardware, so default is commented-out...
# but i want to use it in xorgwizard so leave on...

    Option "RandR" "on"

EndSection

#everything past here is auto-generated by Puppy's Xorg Wizard...


Section "ServerLayout"
	Identifier     "X.org Configured"
	Screen      0  "Screen0" 0 0
	InputDevice    "Mouse0" "CorePointer"
	InputDevice    "Keyboard0" "CoreKeyboard"
EndSection

Section "InputDevice"
	Identifier  "Keyboard0"
	Driver      "kbd"
	Option      "XkbRules" "xorg"
	Option      "XkbModel" "pc102"
	Option      "XkbLayout" "us" #xkeymap0
EndSection

Section "InputDevice"
	Identifier  "Mouse0"
	Driver      "mouse"
	Option	    "Protocol" "auto" #mouse0protocol
	Option	    "Device" "/dev/mouse"
	#Option      "Emulate3Buttons"
	#Option      "Emulate3Timeout" "50"
	Option      "ZAxisMapping" "4 5" #scrollwheel
EndSection

Section "Monitor"
	#DisplaySize	  230   170	# mm
	Identifier   "Monitor0"
	VendorName   "TOS"
	ModelName    "5081"
	HorizSync    31.5-35
	VertRefresh  50-61
	#UseModes     "Modes0" #monitor0usemodes
	Option      "PreferredMode" "800x600"
	EndSection
	
Section "Modes"
	Identifier "Modes0"
	#modes0modeline0
EndSection

Section "Device"
	# Available Driver options are:-
	# Values: <i>: integer, <f>: float, <bool>: "True"/"False",
	# <string>: "String", <freq>: "<f> Hz/kHz/MHz"
	# [arg]: arg optional
	#Option     "AccelMethod"        	# [<str>]
	#Option     "SWcursor"           	# [<bool>]
	#Option     "PciRetry"           	# [<bool>]
	#Option     "NoAccel"            	# [<bool>]
	#Option     "SetMClk"            	# <freq>
	#Option     "MUXThreshold"       	# <i>
	#Option     "ShadowFB"           	# [<bool>]
	#Option     "Rotate"             	# [<str>]
	#Option     "VideoKey"           	# <i>
	#Option     "NoMMIO"             	# [<bool>]
	#Option     "NoPciBurst"         	# [<bool>]
	#Option     "MMIOonly"           	# [<bool>]
	#Option     "CyberShadow"        	# [<bool>]
	#Option     "CyberStretch"       	# [<bool>]
	#Option     "XvHsync"            	# <i>
	#Option     "XvVsync"            	# <i>
	#Option     "XvBskew"            	# <i>
	#Option     "XvRskew"            	# <i>
	#Option     "FpDelay"            	# <i>
	#Option     "Display1400"        	# [<bool>]
	#Option     "Display"            	# [<str>]
	#Option     "GammaBrightness"    	# [<str>]
	#Option     "TVChipset"          	# [<str>]
	#Option     "TVSignal"           	# <i>
	Identifier  "Card0"
	Driver      "vesa" #card0driver
	VendorName  "Trident Microsystems"
	BoardName   "Cyber 9525"
	BusID       "PCI:1:0:0"
EndSection

Section "Screen"
   Identifier "Screen0"
   Device     "Card0"
   Monitor    "Monitor0"
   DefaultDepth 24
   Subsection "Display"
      Depth       24
      Modes       "800x600"
   EndSubsection
EndSection

DeeZ
()
7 комментариев

Debian Lenny + WiFi D-Link DWA110 (USB)

Сразу скажу что опыта пока мало.

Установил на старенький бук Debian (ставил через образ HD-Media + iso), при установке сетевая не нашлась (то ли не определился WiFi свисток то ли что, не знаю). 

Linux TosDD 2.6.26-2-686 #1 SMP Wed Aug 19 06:06:52 UTC 2009 i686 GNU/Linux

После установки, при подключении USB: 

[ 2445.696142] usb 1-1: USB disconnect, address 4
[ 2478.060080] usb 1-1: new full speed USB device using uhci_hcd and address 5
[ 2478.380575] usb 1-1: configuration #1 chosen from 1 choice
[ 2478.652810] phy1: Selected rate control algorithm 'pid'
[ 2478.656530] Registered led device: rt73usb-phy1:radio
[ 2478.656736] Registered led device: rt73usb-phy1:assoc
[ 2478.656928] Registered led device: rt73usb-phy1:quality
[ 2478.666153] usb 1-1: New USB device found, idVendor=07d1, idProduct=3c07
[ 2478.666315] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2478.666437] usb 1-1: Product: 802.11 bg WLAN
[ 2478.666541] usb 1-1: Manufacturer: Ralink
lsusb (в lspci про девайс ничего): 
Bus 001 Device 007: ID 07d1:3c07 D-Link System Wireless G DWA-110 Adapter
lsmod 
rt73usb                22432  0 
rt2x00usb               9792  1 rt73usb
rt2x00lib              22432  2 rt73usb,rt2x00usb
rfkill                  5652  1 rt2x00lib
led_class               3908  1 rt2x00lib
input_polldev           3752  1 rt2x00lib
mac80211              139776  2 rt2x00usb,rt2x00lib
cfg80211               21608  2 rt2x00lib,mac80211
firmware_class          6816  2 rt2x00lib,pcmcia
iwconfig 
wlan0     IEEE 802.11  ESSID:""  
          Mode:Managed  Frequency:2.412 GHz  Access Point: Not-Associated   
          Tx-Power=0 dBm   
          Retry min limit:7   RTS thr:off   Fragment thr=2352 B   
          Encryption key:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

как понял нужен firmware. на дисках нашел только это: 

rt73-modules-2.6.26-2-486 - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on x86
rt73-modules-2.6-486 - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on x86
rt73-modules-2.6.26-2-686-bigmem - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on PPro/Celeron/PII/PIII/P4
rt73-modules-2.6-686-bigmem - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on PPro/Celeron/PII/PIII/P4
rt73-modules-2.6.26-2-xen-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on i686
rt73-modules-2.6-xen-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on i686
rt73-modules-2.6.26-2-openvz-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on PPro/Celeron/PII/PIII/P4
rt73-modules-2.6-openvz-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on PPro/Celeron/PII/PIII/P4
rt73-source - RT73(RT2571W) Wireless Lan Linux Driver - kernel module sources
rt73-modules-2.6.26-2-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on PPro/Celeron/PII/PIII/P4
rt73-modules-2.6-686 - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on PPro/Celeron/PII/PIII/P4
rt73-modules-2.6.26-2-amd64 - Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on AMD64
rt73-modules-2.6-amd64 - Driver for Ralink RT73 wireless network card modules for Linux 2.6 on AMD64
rt73-common - RT73(RT2571W) Wireless Lan Linux Driver - common files

если я правильно понял мне нужно это (выбрал случайно, не очень понимаю отличия остальных): 

Пакет: rt73-modules-2.6.26-2-686
Новый: да
Состояние: не установлен
Версия: 2.6.26+1.0.3.6-cvs20080623-dfsg1-3+lenny1
Приоритет: необязательный
Раздел: contrib/admin
Сопровождающий: Debian Kernel Team <debian-kernel@lists.debian.org>
Размер в распакованном виде: 279k
Зависимости: linux-modules-2.6.26-2-686
Предоставляют: rt73-modules
Описание: Driver for Ralink RT73 wireless network card modules for Linux 2.6.26 on PPro/Celeron/PII/PIII/P4
 This package provides the Driver for Ralink RT73 wireless network card modules
 for the Linux kernel version 2.6.26 on Pentium Pro/Celeron/Pentium II/Pentium
 III/Pentium 4 machines. 
 
 This is the device driver for Ralink RT73 a/b/g WLAN Card.

1. верно ли я двигаюсь? 2. как проверить что firmware установилось корректно и загружается?

Пишут что нужно искать в non-free, но у меня только iso, добавляемые через apt-cdrom add, и как через него проиндексировать non-free не очень понимаю. менять source и поочереди маунтя каждый диск делать update?

DeeZ
()
4 комментария
← назад

RSS подписка на новые темы