История изменений
Исправление Spider55, (текущая версия) :
Купил кабель другой «модели» на 1G и он завёлся (для пробы взял так же на 10G такой же, а вот он не завёлся)
root@router:~# ethtool sfp1
Settings for sfp1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
Port: FIBRE
PHYAD: 0
Transceiver: internal
Supports Wake-on: g
Wake-on: g
Current message level: 0x00000007 (7)
drv probe link
Link detected: yes
root@router:~# ethtool --module-info sfp1
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 550m
Length (62.5um) : 270m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 850nm
Vendor name : OEM
Vendor OUI : 00:90:65
Vendor PN : SFP-1G-DAC0.2M
Vendor rev : 01
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : 2501200010
Date code : 250120
Optical diagnostics support : Yes
Laser bias current : 131.070 mA
Laser output power : 6.5535 mW / 8.16 dBm
Receiver signal average optical power : 6.5535 mW / 8.16 dBm
Module temperature : -0.00 degrees C / 31.99 degrees F
Module voltage : 6.5535 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : On
Laser bias current low alarm : On
Laser bias current high warning : On
Laser bias current low warning : On
Laser output power high alarm : On
Laser output power low alarm : On
Laser output power high warning : On
Laser output power low warning : On
Module temperature high alarm : On
Module temperature low alarm : On
Module temperature high warning : On
Module temperature low warning : On
Module voltage high alarm : On
Module voltage low alarm : On
Module voltage high warning : On
Module voltage low warning : On
Laser rx power high alarm : On
Laser rx power low alarm : On
Laser rx power high warning : On
Laser rx power low warning : On
Laser bias current high alarm threshold : 131.070 mA
Laser bias current low alarm threshold : 131.070 mA
Laser bias current high warning threshold : 131.070 mA
Laser bias current low warning threshold : 131.070 mA
Laser output power high alarm threshold : 6.5535 mW / 8.16 dBm
Laser output power low alarm threshold : 6.5535 mW / 8.16 dBm
Laser output power high warning threshold : 6.5535 mW / 8.16 dBm
Laser output power low warning threshold : 6.5535 mW / 8.16 dBm
Module temperature high alarm threshold : -0.00 degrees C / 31.99 degrees F
Module temperature low alarm threshold : -0.00 degrees C / 31.99 degrees F
Module temperature high warning threshold : -0.00 degrees C / 31.99 degrees F
Module temperature low warning threshold : -0.00 degrees C / 31.99 degrees F
Module voltage high alarm threshold : 6.5535 V
Module voltage low alarm threshold : 6.5535 V
Module voltage high warning threshold : 6.5535 V
Module voltage low warning threshold : 6.5535 V
Laser rx power high alarm threshold : 6.5535 mW / 8.16 dBm
Laser rx power low alarm threshold : 6.5535 mW / 8.16 dBm
Laser rx power high warning threshold : 6.5535 mW / 8.16 dBm
Laser rx power low warning threshold : 6.5535 mW / 8.16 dBm
Исходная версия Spider55, :
Купил кабель другой «модели» на 1G и он завёлся (для пробы взял так же на 10G такой же, а вот он не завёлся)
root@router:~# ethtool --module-info sfp1
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 550m
Length (62.5um) : 270m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 850nm
Vendor name : OEM
Vendor OUI : 00:90:65
Vendor PN : SFP-1G-DAC0.2M
Vendor rev : 01
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : 2501200010
Date code : 250120
Optical diagnostics support : Yes
Laser bias current : 131.070 mA
Laser output power : 6.5535 mW / 8.16 dBm
Receiver signal average optical power : 6.5535 mW / 8.16 dBm
Module temperature : -0.00 degrees C / 31.99 degrees F
Module voltage : 6.5535 V
Alarm/warning flags implemented : Yes
Laser bias current high alarm : On
Laser bias current low alarm : On
Laser bias current high warning : On
Laser bias current low warning : On
Laser output power high alarm : On
Laser output power low alarm : On
Laser output power high warning : On
Laser output power low warning : On
Module temperature high alarm : On
Module temperature low alarm : On
Module temperature high warning : On
Module temperature low warning : On
Module voltage high alarm : On
Module voltage low alarm : On
Module voltage high warning : On
Module voltage low warning : On
Laser rx power high alarm : On
Laser rx power low alarm : On
Laser rx power high warning : On
Laser rx power low warning : On
Laser bias current high alarm threshold : 131.070 mA
Laser bias current low alarm threshold : 131.070 mA
Laser bias current high warning threshold : 131.070 mA
Laser bias current low warning threshold : 131.070 mA
Laser output power high alarm threshold : 6.5535 mW / 8.16 dBm
Laser output power low alarm threshold : 6.5535 mW / 8.16 dBm
Laser output power high warning threshold : 6.5535 mW / 8.16 dBm
Laser output power low warning threshold : 6.5535 mW / 8.16 dBm
Module temperature high alarm threshold : -0.00 degrees C / 31.99 degrees F
Module temperature low alarm threshold : -0.00 degrees C / 31.99 degrees F
Module temperature high warning threshold : -0.00 degrees C / 31.99 degrees F
Module temperature low warning threshold : -0.00 degrees C / 31.99 degrees F
Module voltage high alarm threshold : 6.5535 V
Module voltage low alarm threshold : 6.5535 V
Module voltage high warning threshold : 6.5535 V
Module voltage low warning threshold : 6.5535 V
Laser rx power high alarm threshold : 6.5535 mW / 8.16 dBm
Laser rx power low alarm threshold : 6.5535 mW / 8.16 dBm
Laser rx power high warning threshold : 6.5535 mW / 8.16 dBm
Laser rx power low warning threshold : 6.5535 mW / 8.16 dBm