Ноутбук Vaio VGN-S2XRP c ASPLinux9.0(ядро 2.4.20) В Setup Bios можно изменить только дату и порядок загрузки. Драйвер ehci-hcd ругается, что для его устройства нет прерывания. Есть ли возможность вылечить без перехода на новое ядро? Прилагаю вывод lspci -vv.
lspci -vv
.... 00:1d.0 USB Controller: Intel Corp. 82801DB USB (Hub #1) (rev 03) (prog-if 00 [UHCI]) Subsystem: Sony Corporation: Unknown device 8188 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 4: I/O ports at 1800 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801DB USB (Hub #2) (rev 03) (prog-if 00 [UHCI]) Subsystem: Sony Corporation: Unknown device 8188 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin B routed to IRQ 9 Region 4: I/O ports at 1820 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801DB USB (Hub #3) (rev 03) (prog-if 00 [UHCI]) Subsystem: Sony Corporation: Unknown device 8188 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin C routed to IRQ 0 Region 4: I/O ports at 1840 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801DB USB EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Sony Corporation: Unknown device 8188 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 Interrupt: pin D routed to IRQ 0 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] #0a [2080]