LINUX.ORG.RU

lm_sensors openSUSE не устанавливается


0

0

помогите плиз. почему может быть что sensors после установки ничего не видит, вот логи

[root@main ~]# sensors-detect
# sensors-detect revision 5291 (2008-06-23 23:40:46 -0700)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): YES
Probing for PCI bus adapters...
Use driver `i2c-i801' for device 0000:00:1f.3: Intel ICH9

We will now try to load each adapter module in turn.
Module `i2c-i801' already loaded.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): YES

Module loaded successfully.

We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.

Next adapter: SMBus I801 adapter at 2000 (i2c-0)
Do you want to scan it? (YES/no/selectively): Can't open /dev/i2c-0

Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): YES
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No

Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): YES
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... Yes
Found `Nat. Semi. PC8374L Super IO Sensors'
(but not activated)
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Fintek'... No
Trying family `ITE'... No

Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): YES
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD K10 thermal sensors... No
Intel AMB FB-DIMM thermal sensor... No

Sorry, no sensors were detected.
Either your sensors are not supported, or they are connected to an
I2C or SMBus adapter that is not supported. See doc/FAQ,
doc/lm_sensors-FAQ.html or http://www.lm-sensors.org/wiki/FAQ
(FAQ #4.24.3) for further information.
If you find out what chips are on your board, check
http://www.lm-sensors.org/wiki/Devices for driver status.
[root@main ~]# /etc/init.d/lm_sensors stop
[root@main ~]# /etc/init.d/lm_sensors start
[root@main ~]# /etc/init.d/lm_sensors status
[root@main ~]# sensors -s
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
[root@main ~]#

/etc/init.d/lm_sensors status
даже ничего не показывает.

что я сделал не так?

> Make sure you loaded all the kernel drivers you need.

Видимо, нужно подключить недостающие модули ядра (modprobe <имя_модуля>). Какие именно - зависит от железа.

confluent_anonymous
()
Ответ на: комментарий от confluent_anonymous

где-то есть об этом инфа? почитать бы...

begem0t
() автор топика

У меня ревизия 5666 ( от 2009-02-26) у тебя старье годичной давности. Дальше додумаешь сам ?

SI ★★☆☆
()
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.