Исправление Architector, (текущая версия) :
Либо, если воткнуть и сразу запустить:
root@book:/# usb_modeswitch -v 05C6 -p f000 -V 05C6 -P 6000 -W -M '555342431234567890ABCDEF80000671030000000000000000000000000000'
Take all parameters from the command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 2.5.2 (C) Josua Dietze 2017
* Based on libusb1/libusbx
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x05c6
DefaultProduct= 0xf000
TargetVendor= 0x05c6
TargetProduct= 0x6000
MessageContent="555342431234567890ABCDEF80000671030000000000000000000000000000"
Look for target devices ...
found USB ID 1d6b:0003
found USB ID 0408:5220
found USB ID 0bda:b009
found USB ID 05e3:0608
found USB ID 05c6:f000
vendor ID matched
found USB ID 1d6b:0002
No devices in target mode or class found
Look for default devices ...
found USB ID 1d6b:0003
found USB ID 0408:5220
found USB ID 0bda:b009
found USB ID 05e3:0608
found USB ID 05c6:f000
vendor ID matched
product ID matched
found USB ID 1d6b:0002
Found devices in default mode (1)
Access device 022 on bus 001
Get the current device configuration ...
Current configuration number is 1
Use interface number 0
with class 8
Use endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: Qualcomm, Incorporated
Product: Qualcomm CDMA Technologies MSM
Serial No.: 1234567890ABCDEF
-------------------------
Looking for active drivers ...
OK, driver detached
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Read the response to message 1 (CSW) ...
Response successfully read (13 bytes), status 0
Reset response endpoint 0x81
Reset message endpoint 0x01
Device is gone, skip any further commands
-> Run lsusb to note any changes. Bye!
Никаких изменений
Это все и без сим, и с ней
Исходная версия Architector, :
Либо, если воткнуть и сразу запустить:
root@book:/# usb_modeswitch -v 05C6 -p f000 -V 05C6 -P 6000 -W -M '555342431234567890ABCDEF80000671030000000000000000000000000000'
Take all parameters from the command line
* usb_modeswitch: handle USB devices with multiple modes
* Version 2.5.2 (C) Josua Dietze 2017
* Based on libusb1/libusbx
! PLEASE REPORT NEW CONFIGURATIONS !
DefaultVendor= 0x05c6
DefaultProduct= 0xf000
TargetVendor= 0x05c6
TargetProduct= 0x6000
MessageContent="555342431234567890ABCDEF80000671030000000000000000000000000000"
Look for target devices ...
found USB ID 1d6b:0003
found USB ID 0408:5220
found USB ID 0bda:b009
found USB ID 05e3:0608
found USB ID 05c6:f000
vendor ID matched
found USB ID 1d6b:0002
No devices in target mode or class found
Look for default devices ...
found USB ID 1d6b:0003
found USB ID 0408:5220
found USB ID 0bda:b009
found USB ID 05e3:0608
found USB ID 05c6:f000
vendor ID matched
product ID matched
found USB ID 1d6b:0002
Found devices in default mode (1)
Access device 022 on bus 001
Get the current device configuration ...
Current configuration number is 1
Use interface number 0
with class 8
Use endpoints 0x01 (out) and 0x81 (in)
USB description data (for identification)
-------------------------
Manufacturer: Qualcomm, Incorporated
Product: Qualcomm CDMA Technologies MSM
Serial No.: 1234567890ABCDEF
-------------------------
Looking for active drivers ...
OK, driver detached
Set up interface 0
Use endpoint 0x01 for message sending ...
Trying to send message 1 to endpoint 0x01 ...
OK, message successfully sent
Read the response to message 1 (CSW) ...
Response successfully read (13 bytes), status 0
Reset response endpoint 0x81
Reset message endpoint 0x01
Device is gone, skip any further commands
-> Run lsusb to note any changes. Bye!
Никаких изменений