LINUX.ORG.RU

OpenWrt: настройка принтера SAMSUNG ML-1520 на Backfire (10.03.1)

 


0

1

в чем может быть причина, почему роутер на Openwrt Backfire (10.03.1) не видит принтер (Samsung ML-1520) ? стоят вот такие пакеты

BusyBox v1.15.3 (2011-11-24 04:32:28 CET) built-in shell (ash)
Enter 'help' for a list of built-in commands.
 
  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 Backfire (10.03.1, r29592) ------------------------
  * 1/3 shot Kahlua    In a shot glass, layer Kahlua
  * 1/3 shot Bailey's  on the bottom, then Bailey's,
  * 1/3 shot Vodka     then Vodka.
 ---------------------------------------------------
root@OpenWrt:~# opkg list-installed
base-files - 43.32-r29592
busybox - 1.15.3-3.4
chat - 2.4.4-16.1
comgt - 0.32-9
crda - 1.1.1-1
dnsmasq - 2.55-6.1
dropbear - 0.53.1-5
firewall - 2-34.8
gpioctl - 1.0-1
hotplug2 - 1.0-beta-3
iptables - 1.4.6-3.1
iptables-mod-conntrack - 1.4.6-3.1
iptables-mod-nat - 1.4.6-3.1
iw - 0.9.22-2
kernel - 2.6.32.27-1
kmod-b43 - 2.6.32.27+2011-11-15-1
kmod-cfg80211 - 2.6.32.27+2011-11-15-1
kmod-crc-ccitt - 2.6.32.27-1
kmod-crypto-aes - 2.6.32.27-1
kmod-crypto-arc4 - 2.6.32.27-1
kmod-crypto-core - 2.6.32.27-1
kmod-ipt-conntrack - 2.6.32.27-1
kmod-ipt-core - 2.6.32.27-1
kmod-ipt-nat - 2.6.32.27-1
kmod-ipt-nathelper - 2.6.32.27-1
kmod-mac80211 - 2.6.32.27+2011-11-15-1
kmod-nls-base - 2.6.32.27-1
kmod-ppp - 2.6.32.27-1
kmod-pppoe - 2.6.32.27-1
kmod-switch - 2.6.32.27-4
kmod-usb-core - 2.6.32.27-1
kmod-usb-printer - 2.6.32.27-1
kmod-usb-serial - 2.6.32.27-1
kmod-usb-serial-option - 2.6.32.27-1
kmod-usb2 - 2.6.32.27-1
libc - 0.9.30.1-43.32
libgcc - 4.3.3+cs-43.32
libip4tc - 1.4.6-3.1
libiwinfo - 18
libiwinfo-lua - 18
liblua - 5.1.4-7
libnl-tiny - 0.1-1
libpthread - 0.9.30.1-43.32
librt - 0.9.30.1-43.32
libuci - 12012009.7-4
libuci-lua - 12012009.7-4
libusb - 0.1.12-2
libusb-1.0 - 1.0.8-1
libxtables - 1.4.6-3.1
lua - 5.1.4-7
luci - 0.10.0-1
luci-app-firewall - 0.10.0-1
luci-app-p910nd - 0.10.0-1
luci-i18n-english - 0.10.0-1
luci-lib-core - 0.10.0-1
luci-lib-ipkg - 0.10.0-1
luci-lib-lmo - 0.10.0-1
luci-lib-nixio - 0.10.0-1
luci-lib-sys - 0.10.0-1
luci-lib-web - 0.10.0-1
luci-mod-admin-core - 0.10.0-1
luci-mod-admin-full - 0.10.0-1
luci-proto-3g - 0.10.0-1
luci-proto-core - 0.10.0-1
luci-proto-ppp - 0.10.0-1
luci-sgi-cgi - 0.10.0-1
luci-theme-base - 0.10.0-1
luci-theme-openwrt - 0.10.0-1
mtd - 13
opkg - 576-2
p910nd - 0.95-1
ppp - 2.4.4-16.1
ppp-mod-pppoe - 2.4.4-16.1
uci - 12012009.7-4
udevtrigger - 106-1
uhttpd - 28
usb-modeswitch - 1.1.8-1
usb-modeswitch-data - 20110705-1
usbutils - 003-1
wireless-tools - 29-4
wpad-mini - 20111103-2
zlib - 1.2.3-5

но результата нет

Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 05:51:40 CET 2011
Detected Broadcom 0x6348 CPU revision b0
CPU frequency is 256 MHz
16MB of RAM installed
registering 37 GPIOs
board_bcm963xx: CFE version: 1.0.37-0.8
bootconsole [early0] enabled
CPU revision is: 00029107 (Broadcom BCM6348)
board_bcm963xx: board name: 96348GW-10
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00001000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00001000
On node 0 totalpages: 4096
free_area_init_node: node 0, pgdat 802981f0, node_mem_map 802df000
  Normal zone: 32 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 4064 pages, LIFO batch:0
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes
Memory: 13284k/16384k available (2140k kernel code, 3100k reserved, 453k data, 140k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 254.97 BogoMIPS (lpj=509952)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x001fff]
pci 0000:00:07.0: reg 20 io port: [0xfce0-0xfcff]
pci 0000:00:07.0: supports D1 D2
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:07.0: PME# disabled
pci 0000:00:07.1: reg 20 io port: [0xfce0-0xfcff]
pci 0000:00:07.1: supports D1 D2
pci 0000:00:07.1: PME# supported from D0 D1 D2 D3hot
pci 0000:00:07.1: PME# disabled
pci 0000:00:07.2: reg 10 32bit mmio: [0x000000-0x0000ff]
pci 0000:00:07.2: supports D1 D2
pci 0000:00:07.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:07.2: PME# disabled
pci 0000:01:1e.0: CardBus bridge, secondary bus 0000:02
pci 0000:01:1e.0:   IO window: 0x8008000-0x80080ff
pci 0000:01:1e.0:   IO window: 0x8008400-0x80084ff
pci 0000:01:1e.0:   MEM window: 0x38000000-0x3fffffff
PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
PCI: Setting latency timer of device 0000:01:1e.0 to 64
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.382:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
msgmni has been set to 25
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0300 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: 0x00400000 at 0x1fc00000
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
 CFI mfr 0x000000c2
 CFI id  0x000022a7
 Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.1.
bcm963xx: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
bcm963xx_flash: CFE boot tag found with version 6 and board type 96348GW
bcm963xx_flash: Partition 0 is CFE offset 0 and length 10000
bcm963xx_flash: Partition 1 is kernel offset 10100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset f0000 and length 300000
bcm963xx_flash: Partition 3 is nvram offset 3f0000 and length 10000
bcm963xx_flash: Partition 4 is linux offset 10000 and length 3e0000
bcm963xx_flash: Spare partition is 2b0000 offset and length 140000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000010000 : "CFE"
0x000000010100-0x0000000f0000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x0000000f0000-0x0000003f0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000 
0x0000002b0000-0x0000003f0000 : "rootfs_data"
0x0000003f0000-0x000000400000 : "nvram"
0x000000010000-0x0000003f0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl-fail
Registered led device: ppp
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 140k freed
Please be patient, while OpenWrt loads ...
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
eth1: link forced UP - 100/full - flow control off/off
device eth1.1 entered promiscuous mode
device eth1 entered promiscuous mode
br-lan: port 1(eth1.1) entering forwarding state
Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
Backport based on wireless-testing.git master-2011-11-15
cfg80211: Calling CRDA to update world regulatory domain
roboswitch: Probing device eth0: 
roboswitch: [/home/jow/devel/openwrt/10.03.1/brcm63xx/build_dir/linux-brcm63xx/kmod-switch/switch-robo.c:130] SIOCGETCPHYRD failed!
roboswitch: [/home/jow/devel/openwrt/10.03.1/brcm63xx/build_dir/linux-brcm63xx/kmod-switch/switch-robo.c:130] SIOCGETCPHYRD failed!
No Robo switch in managed mode found, phy_id = 0xffffffff
roboswitch: Probing device eth1: found a 5325! It's a 5350.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: World regulatory domain updated:
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Registered led device: b43-phy0::tx
Registered led device: b43-phy0::rx
Registered led device: b43-phy0::radio
Broadcom 43xx driver loaded [ Features: PL ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:07.2 (0000 -> 0002)
ehci_hcd 0000:00:07.2: EHCI Host Controller
ehci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:07.2: Enabling legacy PCI PM
ehci_hcd 0000:00:07.2: irq 32, io mem 0x30002000
ehci_hcd 0000:00:07.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
nf_conntrack version 0.5.0 (209 buckets, 836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
bcm63xx_ohci bcm63xx_ohci.0: irq 20, io mem 0xfffe1b00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
cfg80211: Calling CRDA for country: UA
cfg80211: Regulatory domain changed to country: UA
cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
b43-phy0: Loading firmware version 508.1084 (2009-01-14 01:32:01)
b43-phy0: Loading firmware version 508.1084 (2009-01-14 01:32:01)
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-lan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-lan: port 2(wlan0) entering forwarding state
root@OpenWrt:~# lsusb
 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 
root@OpenWrt:~# ls /dev/usb/lp*
 
ls: /dev/usb/lp*: No such file or directory
 
root@OpenWrt:~#
root@OpenWrt:~# ls /dev/lp*
 
ls: /dev/lp*: No such file or directory
 

usb 3g модем получилось настроить, вот параллельно во-второй юсб порт подключил 3ж модем и его видит роутер

root@OpenWrt:~# lsusb
 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
 
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
 
Bus 001 Device 003: ID 12d1:1446 Huawei Technologies Co., Ltd. E1552 (HSPA modem)
 

в чем загвоздка, что роутер никак не реагирует на подключение принтера ? возможно каких-то пакетов не хватает ? эксперементировал на другом роутере с прошивкой LEDE - при подключении принтера в usb порт роутера в kernel.log отображается

[ 75.492559] ath: Country alpha2 being used: UA
[ 75.546117] ath: Regpair used: 0x3
[ 75.587160] ath: regdomain 0x8324 dynamically updated by user
[ 83.127944] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 83.382592] device wlan0 entered promiscuous mode
[ 86.081102] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 86.159408] br-lan: port 2(wlan0) entered forwarding state
[ 86.226087] br-lan: port 2(wlan0) entered forwarding state
[ 87.095716] random: nonblocking pool is initialized
[ 88.225594] br-lan: port 2(wlan0) entered forwarding state
[ 437.355103] usb 2-1: new full-speed USB device number 2 using ohci-pci
[ 442.645764] usb 2-1: device descriptor read/all, error -145
[ 442.895137] usb 2-1: new full-speed USB device number 3 using ohci-pci
[ 448.186051] usb 2-1: device descriptor read/all, error -145
[ 448.515336] usb 2-1: new full-speed USB device number 4 using ohci-pci
[ 453.716218] usb 2-1: device descriptor read/all, error -145
[ 453.965003] usb 2-1: new full-speed USB device number 5 using ohci-pci
[ 459.075498] usb 2-1: device descriptor read/all, error -145
[ 459.147994] usb usb2-port1: unable to enumerate USB device

В LEDE установлены такие пакеты

BusyBox v1.25.1 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
 /________/  LE  \  |____|___|___/|___|                      lede-project.org
 \        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (17.01.4, r3560-79f57e422d)
    \________\/    -----------------------------------------------------------

root@LEDE:~# opkg list-installed
base-files - 173.1-r3560-79f57e422d
block-mount - 2017-06-30-bdcb075f-1
busybox - 1.25.1-4
chat - 2.4.7-12
comgt - 0.32-29
dnsmasq - 2.78-1
dropbear - 2017.75-2
firewall - 2017-05-27-a4d98aea-1
fstools - 2017-06-30-bdcb075f-1
fwtool - 1
hostapd-common - 2016-12-19-ad02e79d-6
ip-tiny - 4.4.0-10-cake-legacy
ip6tables - 1.4.21-2
ipset - 6.32-1
iptables - 1.4.21-2
iptables-mod-conntrack-extra - 1.4.21-3
iptables-mod-ipopt - 1.4.21-3
iw - 4.9-1
iwinfo - 2016-09-21-fd9e17be-1
jshn - 2017-02-24-96305a3c-1
jsonfilter - 2016-07-02-dea067ad-1
kernel - 4.4.92-1-4754542a1014bc15342e728589345df7
kmod-ath - 4.4.92+2017-01-31-3
kmod-ath5k - 4.4.92+2017-01-31-3
kmod-cfg80211 - 4.4.92+2017-01-31-3
kmod-fs-f2fs - 4.4.92-1
kmod-gpio-button-hotplug - 4.4.92-2
kmod-hid - 4.4.92-1
kmod-hid-generic - 4.4.92-1
kmod-input-core - 4.4.92-1
kmod-input-evdev - 4.4.92-1
kmod-ip6tables - 4.4.92-1
kmod-ipt-conntrack - 4.4.92-1
kmod-ipt-conntrack-extra - 4.4.92-1
kmod-ipt-core - 4.4.92-1
kmod-ipt-ipopt - 4.4.92-1
kmod-ipt-ipset - 4.4.92-1
kmod-ipt-nat - 4.4.92-1
kmod-lib-crc-ccitt - 4.4.92-1
kmod-mac80211 - 4.4.92+2017-01-31-3
kmod-mii - 4.4.92-1
kmod-nf-conntrack - 4.4.92-1
kmod-nf-conntrack6 - 4.4.92-1
kmod-nf-ipt - 4.4.92-1
kmod-nf-ipt6 - 4.4.92-1
kmod-nf-nat - 4.4.92-1
kmod-nfnetlink - 4.4.92-1
kmod-nls-base - 4.4.92-1
kmod-ppp - 4.4.92-1
kmod-pppoe - 4.4.92-1
kmod-pppox - 4.4.92-1
kmod-scsi-core - 4.4.92-1
kmod-slhc - 4.4.92-1
kmod-usb-core - 4.4.92-1
kmod-usb-hid - 4.4.92-1
kmod-usb-net - 4.4.92-1
kmod-usb-net-cdc-ether - 4.4.92-1
kmod-usb-ohci - 4.4.92-1
kmod-usb-ohci-pci - 4.4.92-1
kmod-usb-printer - 4.4.92-1
kmod-usb-serial - 4.4.92-1
kmod-usb-serial-option - 4.4.92-1
kmod-usb-serial-qualcomm - 4.4.92-1
kmod-usb-serial-wwan - 4.4.92-1
kmod-usb-storage - 4.4.92-1
kmod-usb-uhci - 4.4.92-1
kmod-usb2 - 4.4.92-1
kmod-usb2-pci - 4.4.92-1
kmod-usb3 - 4.4.92-1
lede-keyring - 2017-01-20-a50b7529-1
libblobmsg-json - 2017-02-24-96305a3c-1
libc - 1.1.16-1
libgcc - 5.4.0-1
libip4tc - 1.4.21-2
libip6tc - 1.4.21-2
libiwinfo - 2016-09-21-fd9e17be-1
libiwinfo-lua - 2016-09-21-fd9e17be-1
libjson-c - 0.12.1-1
libjson-script - 2017-02-24-96305a3c-1
liblua - 5.1.5-1
libmnl - 1.0.4-1
libnl-tiny - 0.1-5
libpthread - 1.1.16-1
librt - 1.1.16-1
libubox - 2017-02-24-96305a3c-1
libubus - 2017-02-18-34c6e818-1
libubus-lua - 2017-02-18-34c6e818-1
libuci - 2016-07-04-e1bf4356-1
libuci-lua - 2016-07-04-e1bf4356-1
libuclient - 2017-09-06-24d6eded-1
libusb-1.0 - 1.0.21-1
libxtables - 1.4.21-2
logd - 2017-03-10-16f7e161-1
lua - 5.1.5-1
luci - git-17.290.79498-d3f0685-1
luci-app-firewall - git-17.290.79498-d3f0685-1
luci-app-mwan3 - 1.4-6
luci-app-p910nd - git-19.271.72080-7b230b0-1
luci-base - git-17.290.79498-d3f0685-1
luci-lib-ip - git-17.290.79498-d3f0685-1
luci-lib-jsonc - git-17.290.79498-d3f0685-1
luci-lib-nixio - git-17.290.79498-d3f0685-1
luci-mod-admin-full - git-17.290.79498-d3f0685-1
luci-proto-3g - git-19.271.72080-7b230b0-1
luci-proto-ipv6 - git-17.290.79498-d3f0685-1
luci-proto-ppp - git-17.290.79498-d3f0685-1
luci-theme-bootstrap - git-17.290.79498-d3f0685-1
mtd - 21
mwan3 - 2.0.2-1
netifd - 2017-01-25-650758b1-1
odhcp6c - 2017-01-30-c13b6a05-2
odhcpd - 2017-10-02-c6f3d5d4-2
opkg - 2017-03-23-1d0263bb-1
p910nd - 0.97-5
ppp - 2.4.7-11
ppp-mod-pppoe - 2.4.7-11
procd - 2017-08-08-66be6a23-1
rpcd - 2016-12-03-0577cfc1-1
swconfig - 11
ubox - 2017-03-10-16f7e161-1
ubus - 2017-02-18-34c6e818-1
ubusd - 2017-02-18-34c6e818-1
uci - 2016-07-04-e1bf4356-1
uclient-fetch - 2017-09-06-24d6eded-1
uhttpd - 2017-08-19-3fd58e9b-1
uhttpd-mod-ubus - 2017-08-19-3fd58e9b-1
usb-modeswitch - 2017-05-24-453da8e5-1
usbutils - 007-7
usign - 2015-07-04-ef641914-1
wpad-mini - 2016-12-19-ad02e79d-6
root@LEDE:~#

понятия не имею

у тебя первая сборочка вроде как 2011-12 года, а вторая 2017-18. наверное, прогресс не стоит на месте… у меня к тебе встречный вопрос: почему тебя не устраивает «свежая» сборочка с поддержкой принтера?

anonymous
()
Ответ на: комментарий от anonymous

Так на роутере Asus wl-600g usb порт не на pci

terakon
() автор топика
Ответ на: комментарий от anonymous

Нет не ставил. На LEDE 17 ведь без этих пакетов роутер видит принтер, разве на 10.3.1 без этих пакетов роутер не будет никак реагировать в kernel.log на подключение принтера в юсб порт?

terakon
() автор топика
Вы не можете добавлять комментарии в эту тему. Тема перемещена в архив.